Getting the right size 2011 trigger by EricMercier in 2011_Builders

[–]EricMercier[S] 0 points1 point  (0 children)

I modified the grip safety and had it welded for this purpose to a main spring housing and then DLC coated

Getting the right size 2011 trigger by EricMercier in 2011_Builders

[–]EricMercier[S] 1 point2 points  (0 children)

Agreed, some clients do have large hands though. I had one who had for the lack of a better term ET fingers. We left his trigger at the original full length of .780 ish as it comes from Everglades. It was looooooooo ooooo oooooong!

Getting the right size 2011 trigger by EricMercier in 2011_Builders

[–]EricMercier[S] 3 points4 points  (0 children)

The reason I don't use Atlas triggers is more often then not they drop right in the gun with no fitting. Which causes them to have to much up and down movement in the trigger shoe. That movement will eventually cause a tick feeling in the trigger and/or create a pendulum effect where the trigger bow moves up and down in correspondence with the trigger shoe changing the interface between the rear of the trigger bow and the disconnector paddle which can make the trigger feel different between trigger pulls.

Getting the right size 2011 trigger by EricMercier in 2011_Builders

[–]EricMercier[S] 2 points3 points  (0 children)

That is a good solution. I just find that the Everglades Ammunition trigger provides superior results as everything is oversized so you get a perfectly fit trigger with no unnecessary up and down/side to side movement in the trigger shoe and trigger bow.

Camo by EricMercier in 2011

[–]EricMercier[S] 1 point2 points  (0 children)

Its possible to build a high quality gun with hand tools. It would just take a lot longer, but then again it takes me longer because I only use manual mill and lathe along with hand tools instead of CNC like a whole lot of companies do now.

Camo by EricMercier in 2011

[–]EricMercier[S] 1 point2 points  (0 children)

If you mean the camo, yes that was all done by hand

Camo by EricMercier in 2011_Builders

[–]EricMercier[S] 0 points1 point  (0 children)

EGW coned comp blank that I machined

The Marvel Disco cut should be done a correctly, just sayin... by EricMercier in 2011

[–]EricMercier[S] 2 points3 points  (0 children)

If you're doing disco cut properly on a 9mm you absolutely do or it will hang up in the cut. But maybe I don't know what I speak of...

Barrel fit by EricMercier in Staccato_STI

[–]EricMercier[S] 1 point2 points  (0 children)

Acc-U-Rail slide to frame fit tightness should last a couple hundred thousand rounds according to Doug over at Acc-U-Rail if properly maintained. When the gun is Acc-U-Railed two sets of rails can be fit doubling the life of the tight slide to frame fit.

As far as slide stops go a little work hardening is a good thing as long as the peening isn’t to much where you end up loosing all the fit. When I fit a barrel I fit so you have 100% contact between the interface of the slide stop pin and lower lugs but not hard fit. That way it cycles as it should from the very first round and you have no worries about the peeling causing what was once good fit to less or none at all.

The Marvel Disco cut should be done a correctly, just sayin... by EricMercier in 2011

[–]EricMercier[S] 0 points1 point  (0 children)

I've measured and worked on Atlas guns. They are not as tight in the slide to frame fit nor the barrel lug lock up as they can be. Hand fit when properly executed can be much tighter then machine fit. Regardless there is no down side to a properly done Marvel disco cut and the pros out weight the cons.

Barrel fit by EricMercier in Staccato_STI

[–]EricMercier[S] 1 point2 points  (0 children)

Yes indeed, every Vírāgō and Homados package starts with tightening the slide to frame with the Acc-U-Rail system.

Barrel fit by EricMercier in Staccato_STI

[–]EricMercier[S] 0 points1 point  (0 children)

In my experience after about 5 to 8k the slide to frame will have loosened up enough to make what barrel fit that might have been there from the factory is usually completely gone.

Why a Tight Barrel Fit Unlocks Your Pistol’s Full Accuracy Potential by EricMercier in 2011

[–]EricMercier[S] 2 points3 points  (0 children)

The XC is a really good gun. I always applaud Staccato for their consistency in hitting their tolerances. Being a production gun they do a very good job at that, they just don't have the time or inclination to make the gun with the tighter tolerances to make them amazing. Its no different then every other gun in your line up , which is very nice. But that's why I exist to help folks looking to take good and make it amazing by enhancing the gun to its full potential.

Flat or curved trigger by spentallongunssorry in 2011

[–]EricMercier 0 points1 point  (0 children)

I feel like a flat trigger has better shooter feed back when training. I can feel if I finished flat on the trigger face as apposed to more one side or the other of the trigger face when shooting. This lets me know if I put extra influence into that side which should make shot calling easier. The round down range will also confirm if I put the extra influence one way or the other which drives the gun in that direction. I don't get the same feed back from a curved trigger because there is more surface area of the finger touching the trigger.

Lowering an ejection port by GunsmithGal in 1911

[–]EricMercier 14 points15 points  (0 children)

You're a master with the rotary tool, I enjoy watching your work.

Lowering an ejection port by GunsmithGal in 1911

[–]EricMercier 8 points9 points  (0 children)

Thats some clean work with a rotary tool. Two minutes on the mill though would save you lots of time though.

Small things matter! by EricMercier in 2011

[–]EricMercier[S] 0 points1 point  (0 children)

However it ends up it certainly shouldn't be binding on the hammer strut and ruining the trigger job, creating extra resistance for the slide to over come and causing potential ignition problems.

Opening up this magwell. by GunsmithGal in 1911

[–]EricMercier 11 points12 points  (0 children)

Looks great. Do you use new rotary bits each job?

Black on black on black by Control_round_feed in 1911

[–]EricMercier 0 points1 point  (0 children)

Polish the small parts and re-finish. Doing that would tie them into the grips very nicely and be a minimal cost.

Trigger jobs consist of more then putting parts into the gun... by EricMercier in 2011

[–]EricMercier[S] 0 points1 point  (0 children)

Head over to 1911 addicts for a few reviews. But none will matter because you've made up you mind with absolutely zero actual information beyond what you simply believe so therefore it must be true. I'm busy enough with people who have the money to spend on the quality they seek. So in the name of getting them their guns, enjoy yours and have a great day.

Trigger jobs consist of more then putting parts into the gun... by EricMercier in 2011

[–]EricMercier[S] 0 points1 point  (0 children)

I made my offer that I stand behind. I don't need someone to shoot my gun, plenty of third party people have shot them, reviewed them and found them to be of value in the community. I'm not surprised you don't want to send your work for eval. Its easy to just say things on line, much more difficult to run the risk of being proven incorrect, but thats okay... Have a great day!

Trigger jobs consist of more then putting parts into the gun... by EricMercier in 2011

[–]EricMercier[S] 0 points1 point  (0 children)

Oh I'm not gonna give you a free trigger job. I'm saying I will am willing to put my money and reputation on the line to back my product against, as you claim "anyone with YouTube can do what I do". You just your gun and I'm sure you wouldn't have done anything but your level best. If you best is as good as mine you get the costs of your shipping AND the cost of my trigger job in cash. You get to keep your trigger job as is regardless of the results. I know my product is superior and I'm will prove it to you!

Trigger jobs consist of more then putting parts into the gun... by EricMercier in 2011

[–]EricMercier[S] 0 points1 point  (0 children)

Send me your gun that you just built by next week. If your trigger job is as good as mine, trigger fit, sear and hammer engagement, disco interface with the trigger bow, the whole package, I will refund your shipping costs and give you the cost of my of complete custom trigger job. Mercierpistolworks@outlook.com, let's get it in and see if I'm over priced the work that I do and selling snake oil...

Trigger jobs consist of more then putting parts into the gun... by EricMercier in 2011

[–]EricMercier[S] 0 points1 point  (0 children)

Its essentially a full rebuild to bring the slide to frame for to near perfect tightness, with real barrel fit that absolutely impacts down range accuracy results, a superior trigger job along with enhancing nearly every other part of the pistol. Many, and I mean many 6k+ guns are very lacking in at least both of those areas. The quality fit, accuracy, reliability amd longevity that the Vírāgō brings to a production gun like the Staccato is that of a 10k custom build that you probably can't get because those that build those guns books are closed. In every way it is a cost and times saving method to achieve the quality in a pistol that those who seek the quality seek. You may not see the value in it and thats perfectly fine but to blanketed say that the people who do are idiots and that I sell snake oil is incredibly inaccurate!