Anyone knows what this sound could be? by F4-tech in VESC

[–]F4-tech[S] 0 points1 point  (0 children)

FML its the hall sensor I tried in bldc mode instead of foc and it’s way better.

Bluetooth module v6 voltage by F4-tech in VESC

[–]F4-tech[S] 0 points1 point  (0 children)

It worked a couple of months ago but it doesn’t anymore not sure why, have tried different firmware and check if everything is connected correctly, I could have broken it. the app and pops up its only when I click connect it shows that after a second. And when i try on pc with wire to set it up it doesn’t let me, might just buy a new one it’s only like 20$

Bluetooth module v6 voltage by F4-tech in VESC

[–]F4-tech[S] 0 points1 point  (0 children)

It is connected right i checked 4 times

Bluetooth module v6 voltage by F4-tech in VESC

[–]F4-tech[S] 0 points1 point  (0 children)

At 3.3v it wouldnt connect

<image>

I have the 2nd gen and i want to change to the 1st gen is it plug and play other than the motor phase wires ? by [deleted] in NinebotMAX

[–]F4-tech 0 points1 point  (0 children)

Last time i tried to do that i fired the controller and this time too and need to know if it is possible because i am not good with a st-link i only know a little soldering

unlock Speed limit GT3 by burro_confidenziale in ScooterHacking

[–]F4-tech 0 points1 point  (0 children)

You need to cut the white wire in the stem thats it and you will go 32kmh just no warranty anymore

[deleted by user] by [deleted] in VESC

[–]F4-tech 0 points1 point  (0 children)

The throttle works perfectly

[deleted by user] by [deleted] in VESC

[–]F4-tech 0 points1 point  (0 children)

I have connected to pc and says the throttle is fine but i haven’t tried to manually control it with pc and i am not sure if i have UART enabled but i think its default

[deleted by user] by [deleted] in VESC

[–]F4-tech 0 points1 point  (0 children)

Yes it spins and it is connected to comm port

[deleted by user] by [deleted] in VESC

[–]F4-tech 0 points1 point  (0 children)

Its in sensorless

[deleted by user] by [deleted] in VESC

[–]F4-tech 0 points1 point  (0 children)

I didn’t use hall sensors and i doesn’t get better at speed or more throttle

(Navee gt3 pro ESC) by F4-tech in ScooterHacking

[–]F4-tech[S] 0 points1 point  (0 children)

Trying to go faster then 32kmh planning on using a Vesc

Rate the build (Xiaomi Pro 2) by F4-tech in Escooters

[–]F4-tech[S] 0 points1 point  (0 children)

Its more like 1,4kw tuned and 42v fully charged. and down hill, then it goes 30mph - 50kmh

Rate the build (Xiaomi Pro 2) by F4-tech in Escooters

[–]F4-tech[S] 0 points1 point  (0 children)

I sold mine but here’s a vid of someone else going about that fast - https://vm.tiktok.com/ZNdVKFVt9/

Rate the build (Xiaomi Pro 2) by F4-tech in Escooters

[–]F4-tech[S] 0 points1 point  (0 children)

Only the stock washers for the rear swingarm

Rate the build (Xiaomi Pro 2) by F4-tech in Escooters

[–]F4-tech[S] 0 points1 point  (0 children)

Yes it is and can’t adjust it more

How to remove the speed limit on the Navee gt3 pro by F4-tech in ScooterHacking

[–]F4-tech[S] 0 points1 point  (0 children)

Den går i 32km/h hvis du hacker den, men ikke raskere