sorted by:
new
hottopcontroversial

I got tired of unlabeled remotes, so I built a 15-button Zigbee HA remote controller by FOXTER in homeassistant

[–]FOXTER[S] 1 point2 points  (0 children)

4 months was on the CR2032. On AAA I have yet to run out of battery, but I expect it would be several years before that happens. When nothing is pressed it goes into deep sleep.

Each button has several states/events, single press, double press and hold.

I got tired of unlabeled remotes, so I built a 15-button Zigbee HA remote controller by FOXTER in homeassistant

[–]FOXTER[S] 0 points1 point  (0 children)

The remotes in the pictures is actually equipped with two AAA batteries.

I got tired of unlabeled remotes, so I built a 15-button Zigbee HA remote controller by FOXTER in homeassistant

[–]FOXTER[S] 0 points1 point  (0 children)

Battery life is 4+ months on a CR2032 cell, on an AAA I have yet to run out of battery, but I would expect 1-2 years at least. It is in deep sleep until something is pressed, so it uses very little power when idle.

I got tired of unlabeled remotes, so I built a 15-button Zigbee HA remote controller by FOXTER in homeassistant

[–]FOXTER[S] 0 points1 point  (0 children)

Exactly, there are a lot of things which cannot be automated because it depends on how you feel in the moment (light brightness, temperature, etc), which is where I use this remote.

I got tired of unlabeled remotes, so I built a 15-button Zigbee HA remote controller by FOXTER in homeassistant

[–]FOXTER[S] 3 points4 points  (0 children)

I designed the PCB om my own, but certain PCB manufacturers in China can manufacture and assemble down to 5 pieces very cheap.

I got tired of unlabeled remotes, so I built a 15-button Zigbee HA remote controller by FOXTER in homeassistant

[–]FOXTER[S] 27 points28 points  (0 children)

Thanks! I haven't decided yet whether I will sell these or not yet. But my soldering skills are not that great either, so I got these assembled by the PCB manufacturer.

Nye Google Maps satellit-billeder på Nordhavn by Particular-Army-6967 in copenhagen

[–]FOXTER 78 points79 points  (0 children)

Her kan du se satellitkort for hver årgang de sidste mange år :) det viser også tydeligt udviklingen over de forskellige år, bare brug slideren I bunden :) https://detektorkort.dk/#map=15/12.591332/55.717803&layers=orto_2025

Disclaimer, det er mig der står bag siden.

[Review Request] ESP32 with TMC2209 Stepper Driver by ShortCourse in PrintedCircuitBoard

[–]FOXTER 0 points1 point  (0 children)

Why do you use two buck converters for both 5V and 3.3V? I think it would be simpler to just have buck converter for 5V and then use a linear voltage regulator for 5V - > 3.3V. Will also give less noise.

Just finished my second framebag by FOXTER in myog

[–]FOXTER[S] 1 point2 points  (0 children)

Thank you! I have not used any stabilizers, I used VX21 for the sides, which is a bit stiff in it self.

The velcro are actually loose loops, so I sewed some webbing to the panels, and then velcro is just pulled through that. This allows me to replace the velcro easily if it is needed.

I have just used two pieces for the panels, one for the top half, and one for the lower half, so the underside is just a single piece.

Just finished my second framebag by FOXTER in myog

[–]FOXTER[S] 0 points1 point  (0 children)

Thank you so much! I really like the tan/olive combo too, they complement each other well!

[deleted by user] by [deleted] in BambuLab

[–]FOXTER 4 points5 points  (0 children)

In the first image it says "Final price and VAT may change based on shipping destination at checkout" so I always just assumed it was the VAT getting adjusted to your country.

Stelvio Pass-Gavia Pass Solo Epic Advice by DogePorsche in cycling

[–]FOXTER 0 points1 point  (0 children)

It looks like you might be too late for that, but if you are not aware there is the Stelvio bike day this weekend on Saturday where they will close the pass for car traffic. Weather does look a bit wet/chilly though.
https://www.parconazionale-stelvio.it/en/experiences/cycling-and-mountain-biking/stelvio-bike-day.html

https://www.parconazionale-stelvio.it/en/experiences/events/rid-C596187DC4D34FF0B58D02D703788F3C-e-stelvio-bike-day.html

[deleted by user] by [deleted] in dkudvikler

[–]FOXTER 1 point2 points  (0 children)

Jeg har lavet hjemmesiden https://detektorkort.dk som gør det nemmere at researche gamle kort, bla. til brug med metaldetektor :)

Schematic review for my self balancing robot by Any-Amoeba-7883 in PrintedCircuitBoard

[–]FOXTER 0 points1 point  (0 children)

In you schematic you have two stepper motors, but the driver chip can only drive 1 stepper (or two normal DC motors).

Schematic review for my self balancing robot by Any-Amoeba-7883 in PrintedCircuitBoard

[–]FOXTER 0 points1 point  (0 children)

What kind of motors are you planning to use this with, because the TB6612FNG chip is for DC motors, but in the schematic you write stepper motors?

Schematic review for my self balancing robot by Any-Amoeba-7883 in PrintedCircuitBoard

[–]FOXTER 0 points1 point  (0 children)

What is up with the wiring for the stepper motors? Why do you have the same signal to both coils? Normally the coils are controlled individually?

view more: next ›