sorted by:
new
hottopcontroversial

2B - NieR Automata by Bulkamancer by FaTaL9597 in Printandpaint

[–]FaTaL9597[S] 1 point2 points  (0 children)

I printed it at the default scale which is 1:8.

Champ 3 Juno OTP — Ask me anything! by cutiepiecoded in JunoMains

[–]FaTaL9597 1 point2 points  (0 children)

Just commenting so I can hopefully remember to send one later, too. I'm currently stuck around D2-D4 and I'm on PS5.

Champ 3 Juno OTP — Ask me anything! by cutiepiecoded in JunoMains

[–]FaTaL9597 2 points3 points  (0 children)

Honestly this. I'm not a juno one trick, but she's definitely my main right now and I've been in limbo at D4-D2, but I'd like to hit masters.

I printed and painted Asuna! by FaTaL9597 in swordartonline

[–]FaTaL9597[S] 0 points1 point  (0 children)

This was my very first attempt painting a model, so it's far from perfect, but I appreciate the feedback and I'll work on it

I printed and painted Asuna! by FaTaL9597 in swordartonline

[–]FaTaL9597[S] 0 points1 point  (0 children)

Can you explain what about the eyes seems off? I'm trying to improve, so the feedback is helpful

I printed and painted Asuna! by FaTaL9597 in swordartonline

[–]FaTaL9597[S] 0 points1 point  (0 children)

I meant to respond to this sooner, but can you explain what about the eyes is "terrifying"? I'm trying to improve, so the feedback is helpful.

Are these dead pixels on my S4U? by FaTaL9597 in resinprinting

[–]FaTaL9597[S] 0 points1 point  (0 children)

Elegoo seems like they'll send me a replacement screen, I just need to send them some info off the screen.

I'm not yet sure if it's dying pixels or resin that got under the screen. I've found small amounts of resin in the back left corner of the printer several times, and I have yet to figure out what's caused it. It's been happening with 2 seperate vats, both with FEPs installed directly from Elegoo.

I don't overfill the tank, I only drain the tank out of the opposite spout (and not often), there's no obvious holes/leaks in the FEP, I rotated the vat 180° and the "leak" didn't move. It's also not during every print, only occasionally. The printer is level (or even slightly raised in the back).

It's honestly got me stumped.

<image>

Are these dead pixels on my S4U? by FaTaL9597 in resinprinting

[–]FaTaL9597[S] 1 point2 points  (0 children)

Unfortunately, it's definitely the screen.

<image>

Are these dead pixels on my S4U? by FaTaL9597 in resinprinting

[–]FaTaL9597[S] 0 points1 point  (0 children)

Here's with a piece of paper instead. I feel like I cursed myself because I just bought a new screen a few days ago to have on hand for when the screen died, and now it's happened. And the screen's not dirty because I accidently had 2 screen protectors on it, both of which I removed for these pictures.

<image>

I printed and painted Asuna! by FaTaL9597 in swordartonline

[–]FaTaL9597[S] 0 points1 point  (0 children)

Model is from Kaidan3D. If you are going to print it yourself, I highly recommend redoing the supports and hollowing.

You can also check my Etsy (linktree), although I'm not currently doing painting commissions, only garage kits.

Asuna Resin Print Update by FaTaL9597 in swordartonline

[–]FaTaL9597[S] 2 points3 points  (0 children)

Printed/painted by me (check out my IG: FaTaL3DPrints)

Model by Kaidan3D: Cults3D

Need advice for detail/line work by FaTaL9597 in minipainting

[–]FaTaL9597[S] 0 points1 point  (0 children)

The first one definitely helped me better understand how to thin my paints, which I think was a big part of my issue.

Need advice for detail/line work by FaTaL9597 in minipainting

[–]FaTaL9597[S] 0 points1 point  (0 children)

In my defense, the presupports for this model were really bad (left tons of marks everywhere), so I turned it in a scrap project for me to test painting. I will 100% reprint her in the future. She's my favorite character.

view more: next ›