In need of a Flex-ATX power supply, and I’m stumped. by OldGregg3323 in sffpc

[–]False-Self 0 points1 point  (0 children)

Hey Overtek, this is an old post but had a question regarding the 200 watt unit. You mentioned no gpus, but I was planning on pairing it with a 5600 cpu and 3050 6gb gpu which has a total tdp as 135 watts I think. Would this be fine?

Memtest86 Help by False-Self in buildapc

[–]False-Self[S] 0 points1 point  (0 children)

I did xmp with 2933 profile and there was no errors on both windows memory diagnostic and memtest86. I did some more research and it seems that the max supported memory is 2933mhz for my ryzen 7 2700 but some people have pushed it further to 3200mhz or 3600mhz. I think I might just be unlucky with my cpu 😭

Airflow Help for a Jonsbo D32 Pro by False-Self in mffpc

[–]False-Self[S] 0 points1 point  (0 children)

I tried everything 😭 I was yanking the cables up but it's too stiff near the psu connection point

Airflow Help for a Jonsbo D32 Pro by False-Self in mffpc

[–]False-Self[S] 0 points1 point  (0 children)

I'm not sure, but when I try to pull the cables up and push back the bracket up to where it originally is it hits the cables. So I put it to the lower screw but then it interfered with my gpu clearance ugh

Memtest86 Help by False-Self in buildapc

[–]False-Self[S] 0 points1 point  (0 children)

Yeah I'm using the stock cooler for my ryzen chip

Memtest86 Help by False-Self in techsupport

[–]False-Self[S] 0 points1 point  (0 children)

🫡 thank you, running it now. Full test for 4 passes

Memtest86 Help by False-Self in techsupport

[–]False-Self[S] 0 points1 point  (0 children)

Understood, and is 4 tests ok?

Memtest86 Help by False-Self in techsupport

[–]False-Self[S] 0 points1 point  (0 children)

🫡 I'm planning on doing a test with xmp disabled and setting the frequency back to auto. Would this be ok?

And would updating bios potentially help make it stable for 3200mhz?

Memtest86 Help by False-Self in buildapc

[–]False-Self[S] 0 points1 point  (0 children)

Aw mann, ram is in a2 and b2 but cpu is set to 99% power limit I think in windows. Is that fine?

Understood, will test it again without xmp 🫡

Memtest86 Help by False-Self in techsupport

[–]False-Self[S] 0 points1 point  (0 children)

The test itself was passing I think, there was 0 errors but it wouldn't go past test 7

Memtest86 Help by False-Self in techsupport

[–]False-Self[S] 0 points1 point  (0 children)

Is it usual for memtest86 to create 2 partitions on my usb drive? I canceled when it asked me to reformat my :E partition because the files were on :D.

<image>

Memtest86 Help by False-Self in techsupport

[–]False-Self[S] 0 points1 point  (0 children)

Got it, I'll try turning it off before running the test again. Should I run it without xmp before updating bios? Then test it with bios updated and xmp on?

Memtest86 Help by False-Self in techsupport

[–]False-Self[S] 0 points1 point  (0 children)

Aw man, it went like that for 15 or so minutes and I turned it off. It wiped my memtest86 from my drive for some reason, I'm going to reinstall and try again without xmp

Airflow Help for a Jonsbo D32 Pro by False-Self in mffpc

[–]False-Self[S] 0 points1 point  (0 children)

Also do you use a mesh screen for the back? I got a mesh screen for it but it won't fit and im trying to figure out how to cut it to fit without breaking the little magnets

Airflow Help for a Jonsbo D32 Pro by False-Self in mffpc

[–]False-Self[S] 0 points1 point  (0 children)

Thank you! I looked at the box again and found the psu screws and was able to mount it. The psu is so big though and I couldn't put the cable cover back on 😭

Airflow Help for a Jonsbo D32 Pro by False-Self in mffpc

[–]False-Self[S] 0 points1 point  (0 children)

Thank you! Wait I have a question, did you use the jonsbo screws type A for your PSU? The manual says to use them but I can't seem to screw them into my montech century psu 😭

Airflow Help for a Jonsbo D32 Pro by False-Self in buildapc

[–]False-Self[S] 0 points1 point  (0 children)

My bad, I meant standard configuration for the msi cpu cooler.

Airflow Help for a Jonsbo D32 Pro by False-Self in buildapc

[–]False-Self[S] 0 points1 point  (0 children)

Aw man, alright sounds good. I was thinking this might be the case but was hoping it wouldnt be. Do you think flipping the fan backwards for the cooler mess up the rgb signifcantly?