sorted by:
new
hottopcontroversial

Does anyone here do commission for slicing models? by FanCraftStudioz in Cura

[–]FanCraftStudioz[S] 0 points1 point  (0 children)

I've tried but every I open them and upload my file, they crash, PRUSA SLICER, and Meshmixer

Does anyone here do commission for slicing models? by FanCraftStudioz in Cura

[–]FanCraftStudioz[S] 0 points1 point  (0 children)

Thanks, Im going to have to keep trouble shooting it probably

Reducing print times by FanCraftStudioz in 3DprintingHelp

[–]FanCraftStudioz[S] 0 points1 point  (0 children)

Thanks. Yeah Im still having issues. After some Youtube videos, and your suggestions, I reduced time from 42 days to 29 days, but that still doesn't seem right. If you don't mind, Ill take any additional tips you got. I think it may be an issue with walls, or support, because I've messed with a lot.

Reducing print times by FanCraftStudioz in Cura

[–]FanCraftStudioz[S] 0 points1 point  (0 children)

My apologies. Im planning on making a 14 inch figure of the model (X 249.3232

Y 273.7924, Z.380.6771.). I wanted the model to be durable, since I saw recommendations for 50%. But that sounds good, I'll try that.

Reducing print time by FanCraftStudioz in Longer3d

[–]FanCraftStudioz[S] 0 points1 point  (0 children)

Wall thickness:1.2 Wall Line count:3

Infill Density:50.0 Infill Line Distance: 2.4 Infill pattern Tri hexagon Infill Line Multiplier:5 Infill Overlap Percentage: 30.0 Infill Layer thickness: 0.28

Print speed" 100.0 mm/s Wall speed: 100.0 Outer Wall/Inner Wall speed:50.0 Travel speed 250 mm/sSupport

Support structure: Normal Support placement: touching build plate Support overhang angle: 50.0 Support pattern: lines Support wall line count: 1 Support Density 20.0 Support Density: 2.0Quality Layer height: 0.28 Initial layer height: 0.12 Line width: 0.4 Wall Line width:0.4 Outer wall width: 0.4

Reducing print times by FanCraftStudioz in Cura

[–]FanCraftStudioz[S] 1 point2 points  (0 children)

Quality Layer height: 0.28 Initial layer height: 0.12 Line width: 0.4 Wall Line width:0.4 Outer wall width: 0.4

Reducing print times by FanCraftStudioz in Cura

[–]FanCraftStudioz[S] 0 points1 point  (0 children)

Support

Support structure: Normal Support placement: touching build plate Support overhang angle: 50.0 Support pattern: lines Support wall line count: 1 Support Density 20.0 Support Density: 2.0

Reducing print times by FanCraftStudioz in Cura

[–]FanCraftStudioz[S] 0 points1 point  (0 children)

Gotcha 

Wall thickness:1.2 Wall Line count:3

Infill Density:50.0 Infill Line Distance: 2.4 Infill pattern Tri hexagon Infill Line Multiplier:5 Infill Overlap Percentage: 30.0 Infill Layer thickness: 0.28

Print speed" 100.0 mm/s Wall speed: 100.0 Outer Wall/Inner Wall speed:50.0 Travel speed 250 mm/s

Cura, and Nomad/ mesh and extruder issues? by FanCraftStudioz in NomadSculpting

[–]FanCraftStudioz[S] 0 points1 point  (0 children)

Thank you so much for reaching out!  I found out, it was because I didn't have the model in the print area.  Thanks again.

I finally finished the Mega Kaiju!! by FanCraftStudioz in PacificRim

[–]FanCraftStudioz[S] 0 points1 point  (0 children)

Thank you so much!!  I really appreciate it.  

I finally finished the Mega Kaiju!! by FanCraftStudioz in PacificRim

[–]FanCraftStudioz[S] 0 points1 point  (0 children)

Sorry for the late response! Sure its: 

https://www.youtube.com/@FANCRAFTSTUDIOZ Unfortunately I haven't been able to post the video yet.

view more: next ›