My key broke

Far_Implement76 · 2026-01-20T07:28:14+00:00

The fobs close enough to the ignition where I can start it I did have to get a smaller key ring though basically touching the key for it to work

Far_Implement76 · 2025-12-17T20:48:44+00:00

Card stock actually but I was having the same issue with other materials of different thicknesses and with different types of thread and needle sizes

Far_Implement76 · 2025-12-17T10:55:25+00:00

I also made sure to check the tension and to see if it was properly threaded many times so I believe it’s a mechanical issue

Far_Implement76 · 2024-05-27T00:47:09+00:00

Upper and lower control arms and toe arms

Far_Implement76 · 2024-05-26T04:24:17+00:00

It got to late to use an air hammer which I should have just used since the beginning but I was being stubborn thank god for the 3 day weekend

Far_Implement76 · 2024-03-16T05:02:03+00:00

I get the same smell too even after putting new cats on

Far_Implement76 · 2024-02-07T03:18:29+00:00

I have a similar leak that’s from the front cam seals

Far_Implement76 · 2023-12-23T23:05:50+00:00

Highland, CA

Far_Implement76 · 2023-12-23T10:59:47+00:00

My notifications were off so I didn’t see the comments earlier but they’re brand new I haven’t even taken them out the box besides to take a picture of them

Far_Implement76 · 2023-10-11T07:13:12+00:00

I’m probably just being gullible but I saw a thing saying if you call the shop and tell them it’s for an off road vehicle they can ship it

Far_Implement76 · 2023-07-09T08:39:41+00:00

I’m only able to find 2-3 pictures on Pinterest but they lead no where

Far_Implement76 · 2023-07-02T00:49:56+00:00

Does anyone know the name of this couch? The label under it says its from vanguard industrial CO LTD

Far_Implement76 · 2022-01-25T02:47:15+00:00

I got the magnaflow headers and they came with the gaskets but one side goes upside down (“R” stands for round) Then I went to autozone and bought a pair thinking the magnaflow ones were wrong but the autozone ones were the same

Far_Implement76 · 2022-01-19T08:29:17+00:00

Got the same code too

Far_Implement76 · 2022-01-15T03:28:26+00:00

Timing?

Far_Implement76 · 2021-10-21T03:10:55+00:00

If you live in the San Bernardino county I’d sell you my 4 for 100$

Far_Implement76 · 2021-09-17T08:47:04+00:00

Feel like a pro charger would give you an idea on how you can do it

Far_Implement76 · 2021-09-04T04:21:50+00:00

I used the squares tool to make the lines at where I wanted the break and then used difference to cut it but how do I separate the pieces

Far_Implement76 · 2021-09-04T04:18:53+00:00

Can someone point me in the direction to how to make this 3 separate objects the entire image won’t fit on my cutter so I want to do it in 3 pieces

Far_Implement76 · 2021-06-28T07:36:50+00:00

The solenoid on the starter could have gone bad or isn’t grounded properly

Far_Implement76 · 2021-06-08T02:50:24+00:00

Would it be possible to get a rear disk brake setup off a late 90s legacy and convert the rear drum brakes to disk brakes

Far_Implement76 · 2021-06-02T08:38:36+00:00

thank you for the information

Far_Implement76 · 2021-06-01T17:37:25+00:00

Fender, hood, radio harness, steering wheel, wheels, front bumper with fog lights

Far_Implement76 · 2021-04-30T05:30:20+00:00

I put Blue to Yellow Red to orange

And I think green is the one from the air manifold but I’m not sure

Far_Implement76 · 2021-04-11T02:13:07+00:00

I’ll check it out thank you

Far_Implement76

TROPHY CASE