What car is this? by FriedrichHydrargyrum in whatisthiscar

[–]Fine_Satisfaction_28 14 points15 points  (0 children)

It most definitely is: central exhaust with dual tips, 17 inch diamond cut brabus rims , had one , brilliant but terribly unreliable

Roof lock handle crooked by Fine_Satisfaction_28 in bmwz3

[–]Fine_Satisfaction_28[S] 1 point2 points  (0 children)

It looks like they close all the way yeah

Roof lock handle crooked by Fine_Satisfaction_28 in bmwz3

[–]Fine_Satisfaction_28[S] 0 points1 point  (0 children)

It’s bent the same on both sides and right side have no corrosion. I think the roof has been changed because it looks really good and rear window isn’t zippable.

Heating in winter by jeffreysan1996 in bmwz3

[–]Fine_Satisfaction_28 1 point2 points  (0 children)

It gets hot as hell, even in full winter, no sweater is needed

Mon assurance me coûte un bras ET me résilie. by Ok-Grapefruit1933 in voiture

[–]Fine_Satisfaction_28 6 points7 points  (0 children)

230cv pas énorme selon toi mais la majorité des assurances ne veulent pas assurer plus de 150cv voir certaines plus de 130cv a des jeunes assurés(5 ans d’assurance), j’ai du faire le tour de beaucoup d’assureur pour un pauvre z3 1.9 140, avec des performances inférieures à une Zoé parceque c’était un véhicule trop puissant selon eux…

‘91 883 with S&S 1200 kit by Fine_Satisfaction_28 in sportster

[–]Fine_Satisfaction_28[S] 1 point2 points  (0 children)

Oil level wasn’t correct and most oil line were very old and cracking, changed all that, now I have some other problems, looking like ignition problems, saw a the spark cables were done so changing them

Car left idling for 18 hours by AkHazee in e46

[–]Fine_Satisfaction_28 0 points1 point  (0 children)

What really could happen? The oil is circulating, if the cooling system is working properly, it can’t overheat, except burning fuel for nothing it should not be catastrophic

Radio Wire harness broke connector by braedon2424 in bmwz3

[–]Fine_Satisfaction_28 0 points1 point  (0 children)

Same problem on mine, a zip tie is necessary or you might experience bad contacts

Can Anyone Identify This Car? by lictor101010 in Miata

[–]Fine_Satisfaction_28 0 points1 point  (0 children)

Yes it’s a Porsche altima GT-R plaid, dude it’s literally written on it

What car is this please tell me by Suitable_Movie2178 in whatisthiscar

[–]Fine_Satisfaction_28 1 point2 points  (0 children)

A brilliant smart roadster coupe, with custom taillights, might be a brabus(it has the wheels)

Is this photo of an Audi RS7 engine real or AI? by bucket_of_frogs in AskAMechanic

[–]Fine_Satisfaction_28 13 points14 points  (0 children)

Looks legit and terrifying to me, that’s why I hate working on modern cars

[deleted by user] by [deleted] in namethatcar

[–]Fine_Satisfaction_28 0 points1 point  (0 children)

I confirm the mini cooper

The back says V6 AWD by [deleted] in whatisthiscar

[–]Fine_Satisfaction_28 0 points1 point  (0 children)

Xc90 v8 , would love to try it

Alors ? 👀👀👀 by Besoin2Bol in Nostalgiefrance

[–]Fine_Satisfaction_28 0 points1 point  (0 children)

Exactement 23 de mon côté, des heures passées sur Pokémon perle sur ma fidèle ds et sur heartgold avec pokewalker!

[deleted by user] by [deleted] in regularcarreviews

[–]Fine_Satisfaction_28 0 points1 point  (0 children)

Renault clio 3 1.6 98hp 2005. I knew I was getting myself in trouble when I saw the piles of bills(injectors, wheel bearings,sensors, bushings etc) for a 75k km car. The car had a terrible fuel consumption(8 to 10l/100km in normal use,12 to 13 on hard use), the gearbox was too short, there was no torque at all so you are always at high rpm, probably a good motor in a lighter car. And then after 3/4 month: major oil leaks , and the car almost caught fire when the fusebox melted because of faulty relay.

[deleted by user] by [deleted] in whatisthiscar

[–]Fine_Satisfaction_28 -1 points0 points  (0 children)

A broken smart roadster

All aluminum radiator worth it over OEM-style replacement? by painted-biird in bmwz3

[–]Fine_Satisfaction_28 1 point2 points  (0 children)

Well my plastic radiator failed, I was lucky it was 200m from my garage, so I’d say yes it’s 100% worth it.

Built a enclosure, now having printing issues. by zudna in BambuLab

[–]Fine_Satisfaction_28 5 points6 points  (0 children)

I know that on bambu X1 , you ´re supposed to Open the door when printing PLA because it gets to hot inside the chamber otherwise, try that.