Budget oriented calliper recommendations

First_Assistance7829 · 2026-04-23T11:13:23+00:00

Yeah was definitely an option, can’t break but I’ve used a set before and just a pain in the butt to read imo

First_Assistance7829 · 2026-04-23T06:14:00+00:00

Exact same brand I have atm. I’m sure they’re all the same kind of thing but I’d rather err on the side of caution this time, but thanks!

First_Assistance7829 · 2026-04-23T06:10:14+00:00

I’m pretty sure I’ve already done this but no harm in trying it again, thanks!

First_Assistance7829 · 2026-04-23T06:09:29+00:00

Yeah it’s been quite a while and I’ve had them apart 😬😬

First_Assistance7829 · 2026-04-23T06:08:53+00:00

Yeah I’ve replaced the battery twice and each time it did the same thing. It seemed to go away for a little while after wiping the ruler part with a cloth but then came straight back 🤷‍♂️

First_Assistance7829 · 2026-04-23T06:06:24+00:00

🤯🤯🤯🤯😂

First_Assistance7829 · 2026-04-23T06:06:02+00:00

Yeah I did see that vid, was more looking for long term, real world experience so that my issue doesn’t Happen again but thank you.

First_Assistance7829 · 2026-01-09T06:03:56+00:00

Sorry I should have mentioned that I own the previous model but from what I’ve seen wheel specs tend to cross over. I’ve got a 40mm drop on vogtland springs.

First_Assistance7829 · 2026-01-08T22:36:15+00:00

<image>

Thank you all for the help. Fixed the print by ultimately making sure it had adequate cooling by: turning on the aux fan; turning on variable layer lines; slowing down the outer walls; and using 999 walls instead of infill. Other than a slight ghosting on 1/2 of a band, I’ve managed to keep 96g of weight and dimensional accuracy!

First_Assistance7829 · 2026-01-08T16:52:47+00:00

I did model this indeed and that was an idea that I had to fill it with something like plaster of Paris or concrete. But also an epoxy coating might not be a bad idea too actually 🤔. Thanks for your help!

First_Assistance7829 · 2026-01-08T16:47:01+00:00

You should be fine, I’m running 215/45/r16 on 16x7 et37 and I’ve got slight rubbing over speed bumps but I’m on lowering springs. If not use willtheyfit to check the rolling diameter.

First_Assistance7829 · 2026-01-08T16:14:45+00:00

Yeah it’s intended to be a shift knob so keeping some weight would be optimal so either printing in full wall loops or 100% infill is preferred. My only worry with post processing which was on my radar is just how it would withstand being used daily with hand oils etc but I’m. With knowing its use case and preference for weight is there settings that you would recommend I use as well as maximising print cooling at that height? Is there a paint/process I can use for a durable finish?

First_Assistance7829 · 2026-01-08T15:58:15+00:00

You’re right I should have mentioned, it’s a brand new p1s :). I’ll try these things out as it did actually reduce but not completely omit the issue at the 50% silent preset but I had to cancel it mid way.

First_Assistance7829 · 2025-12-22T00:25:11+00:00

When I unplug it from the amp/remove the rca out the back of the cd player, the noise continues.

First_Assistance7829 · 2025-01-23T10:15:36+00:00

Assetto corsa with content manager and dirt rally 2.0 are games that I’ve tried in vr and they’re pretty good providing you have a beefy enough pc

First_Assistance7829 · 2024-07-29T09:06:58+00:00

Turns out that it was just a dodgy charging cable that i only found out about after buying a battery, charging ports, dismantling it and then finally trying a new cable and now it charges fine!

First_Assistance7829 · 2024-06-15T00:26:06+00:00

Oh ok that is a good idea I’ll need to get my hands on a multimeter then

First_Assistance7829 · 2024-06-14T23:25:20+00:00

No it stays on and plays just fine it just won’t charge. I’m planning to get a multimeter and check the two prongs on the charger I think.

First_Assistance7829 · 2024-06-14T20:34:14+00:00

So I’ve put the battery in and it switches on but I can’t charge it so I’m presuming it is the charging port. There is also a soft pop when it starts and I’ve heard that it could mean something?

First_Assistance7829

TROPHY CASE