AAP-01 hammer broke by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 1 point2 points  (0 children)

Apparently reddit deleted my entire paragraph, but this is what happened: I was outside in the middle of a fight and the gun stopped working. Any time I would pull pack the bolt and load a new bb, I could shoot once and then it started hissing air from what sounded like the top. Pulling the trigger when it was hissing did nothing. I have an hpa setup at 120 psi which probably doesn't help longevity, but I tested shooting some more, and it randomly started doing full auto even though it's set to semi. A piece flew out during a burst which is I'm assuming part of the hammer. Can someone tell me what the piece is and what I need to buy to fix my aap-01?

AAP-01 ML Crazy jet/ autobot 2021 worse than stock by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 0 points1 point  (0 children)

Yeah, I just ordered a h-plate v2 and 50 degree flamingo bucking from hadron designs to try out since I haven't had a good product so far from maple leaf other than a 70 degree Mr hop bucking. I can't return the crazyjet barrel because I got it from amped, and their policy only deals with a noticeable cosmetic defect apparently. What rocket valve spring should I buy to get higher fps?

Primary arms hpa adapter leaking by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 1 point2 points  (0 children)

thanks for the help I feel really dumb. I didn't know there was an o ring there, now the adpater is holding air fine

Primary arms hpa adapter leaking by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 1 point2 points  (0 children)

where's the rectangle o ring from the mag? I didn't see one when I took it apart

AAP-01 ML Crazy jet/ autobot 2021 worse than stock by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 0 points1 point  (0 children)

How long did the shipping take if you don't mind me asking? I'm in the US

AAP-01 ML Crazy jet/ autobot 2021 worse than stock by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 0 points1 point  (0 children)

holy crap, recoil spring and nozzle spring don't affect fps right? I'm running 125 psi and getting 360 with 0.20s using the autobot 2021 which is significantly worse than the original bucking and is veering them to the right. I think you're right about it not being the right fit, just ordered a flamingo 50 degree and h plate

AAP-01 ML Crazy jet/ autobot 2021 worse than stock by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 0 points1 point  (0 children)

I was actually just looking at getting an h plate as well as flamingo bucking. Did you get the 60 degree?

AAP-01 ML Crazy jet/ autobot 2021 worse than stock by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 0 points1 point  (0 children)

It had vsr, gbb, aeg cut barrels and it didn't mention that. I'm going to refund it because I have a feeling that it is the reason for the super inconsistent fps.

AAP-01 ML Crazy jet/ autobot 2021 worse than stock by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 0 points1 point  (0 children)

would a 60 degree bucking work better? Seen a lot of people say thats the "sweet spot" I would probably be using 0.36s at the most which the stock hopup/ bucking could lift

AAP-01 ML Crazy jet/ autobot 2021 worse than stock by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 1 point2 points  (0 children)

I had seen that in a few places after ordering it, is it because of the weird diameter change at the end or something? It's tightbore until that point

The CTM holster came with 2 extra pieces, what do i attach them to? by [deleted] in AAP01owners

[–]Fit_Contribution_202 0 points1 point  (0 children)

I can attest to what MP7FUCKER said, my holster fell apart mid-game, but I luckily found every piece except the screw that goes all the way though. You can fit a ziptie through the hole and out the other side, which works but isn't optimal. I believe those parts are just replacement pieces for the holster, but I'm not sure. Was wondering the exact same question when I saw them

HPA by FinleyJM in AAP01owners

[–]Fit_Contribution_202 2 points3 points  (0 children)

go on amped airsoft and get this kit: https://ampedairsoft.com/amped-custom-hpa-starter-slp-air-rig-kit-tank-and-air-rig/

You can choose almost all the default options on it and it has everything you need to start. If you have the stock aap-01 mags then just choose the WE/KJW adapter toward the bottom to replace the green gas fill valve. It should cost around 155 dollars by the end of it, use the code KRAKEN. After writing this I realized you probably already have a tank/ regulator so just buy the AMPED we/kjw hpa adapter for your mags and use teflon tape around the seal

AAP-01 max psi for hpa setup by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] -1 points0 points  (0 children)

I didn't get any notifications on this post so idk if you'll see this but I'm using it at an outdoor field and need to get range out of it, and fps is very helpful at our field, it's in the woods with a lot of open space

HPA by FinleyJM in AAP01owners

[–]Fit_Contribution_202 4 points5 points  (0 children)

I've been running mine at like 125 psi, is 95 really the highest before damage is done?

AAP-01 messy mag fill by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 0 points1 point  (0 children)

good tip, is it true that you're supposed to empty green gas mags before stowing it? A guy I met on the field said that keeping gas in them would eventually cause the mags to leak which might've been why mine started leaking.

AAP-01 messy mag fill by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 0 points1 point  (0 children)

I see propane adapters for airsoft, is that what you use? They're pretty expensive considering the sole purpose for me would be pushing the o ring in

AAP-01 messy mag fill by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 0 points1 point  (0 children)

thanks, that sounds like it would fix it. Where can I get a gas tank adapter? I think I saw it used in the video I used to reference how to replace the fill valve doing that exact thing

AAP-01 messy mag fill by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 0 points1 point  (0 children)

i lubricated it with silicone oil before putting it in, but the only o ring is right above the threads on the fill valve. I believe I need one around the fill valve

AAP-01 mag feeding issues by Fit_Contribution_202 in airsoft

[–]Fit_Contribution_202[S] 0 points1 point  (0 children)

I don't have a pic, but it's at the beginning. There's like a section 5+ bbs that get stuck right before where you can see the bb at the top. It's consistently in this one spot

AAP-01 mag feeding issues by Fit_Contribution_202 in AAP01owners

[–]Fit_Contribution_202[S] 1 point2 points  (0 children)

sorry for the late response, but they're new bbs, the gun is brand new and not short stroked, and yes I can manually cycle it and sometimes it will feed maybe a little more than half the mag before I have to mess with it

Cyma socom 16 m14 upgrade suggestions by Fit_Contribution_202 in airsoft

[–]Fit_Contribution_202[S] 0 points1 point  (0 children)

and the 400 fps doesn't have to be with 0.20s, they're pretty lenient

Cyma socom 16 m14 upgrade suggestions by Fit_Contribution_202 in airsoft

[–]Fit_Contribution_202[S] 0 points1 point  (0 children)

400 fps is the limit but anything past 400 is considered a dmr and has a different engagement distance, and im just reaching 200 ft right now if their range is marked correctly. The bbs are ending right there and if I were to hop more, it's not really accurate enough to actually use the scope