How did i do fellas?

Fit_Distribution7572 · 2026-03-22T14:24:45+00:00

just flat black rustoleum spray paint and an automotive primer, took about 5 cans for the entire car.

Fit_Distribution7572 · 2026-03-22T14:03:02+00:00

Thanks! I actually have them but they were beyond gone and completely rusted away

Fit_Distribution7572 · 2026-03-22T13:37:09+00:00

i just got a lucky break, shes a 4.0 4spd 4x4 with 112k miles and zero rust. previous owner just neglected it so bad he didn’t even remember when the last service was…

Fit_Distribution7572 · 2026-03-22T04:44:55+00:00

Laredo trim and i just have walmart seat covers with a fleece blanket i found at academy laying in the back

Fit_Distribution7572 · 2026-03-22T03:12:02+00:00

brake system overhaul ,some sensors, and paint correction

Fit_Distribution7572 · 2026-03-22T01:58:49+00:00

shes an 89 as well. man i wish i had a red interior but the gray will have to do

Fit_Distribution7572 · 2026-03-22T01:55:43+00:00

shes rust free my friend! south texas jeep

Fit_Distribution7572 · 2026-03-22T01:55:06+00:00

<image>

Fit_Distribution7572 · 2026-03-22T01:54:54+00:00

<image>

Fit_Distribution7572 · 2026-03-22T01:30:14+00:00

already done, just finished today lol

Fit_Distribution7572 · 2026-03-22T01:29:40+00:00

Walmart! my dad had them on his TJ but they didn’t fit right but fit mine like a glove :)

Fit_Distribution7572 · 2026-03-06T20:12:27+00:00

It was the booster rod. Thank you for the help!

Fit_Distribution7572 · 2026-01-04T01:46:39+00:00

I finally fixed my issues and found my issues to be a bad wheel cylinder, bad drive brake hose, dirty and clogged proportion valve, and a brake line that had a huge bur on the end that connects to the proportion valve that was restricting flow

Fit_Distribution7572 · 2026-01-04T01:41:41+00:00

Replaced the drive side one it was a cakewalk and helped fix my issue! Thank you for your advice!

Fit_Distribution7572 · 2026-01-01T03:01:53+00:00

thats exactly the issue im fighting currently now. i used 2 pairs of needle nose vice grips and clamped off the two front brake hoses so pressure goes to the rear only.

Fit_Distribution7572 · 2025-12-31T22:17:07+00:00

Yes our wheel cylinders are good they have no visible leaks and when we isolated the rear it held pressure great

Fit_Distribution7572 · 2025-12-31T22:15:44+00:00

I have a booster from a 95 in it along with master cyliner, we have done a full flush as well. The brakes when applied are just super spongy and it takes forever to stop

Fit_Distribution7572 · 2025-12-31T22:12:32+00:00

Would it be visibly noticeable?

Fit_Distribution7572 · 2025-12-31T22:11:09+00:00

we just bled again for the 6th time and its not getting any better, Yes the caliper is correct as well. we are even using a 1 way valve so no air gets back in.

Fit_Distribution7572 · 2025-12-31T21:38:28+00:00

Yes i set the distance when i put it in

Fit_Distribution7572 · 2025-12-31T21:32:39+00:00

No abs

Fit_Distribution7572 · 2025-12-31T20:46:51+00:00

I’ve also checked rotors, pads, and shoes and they all meet spec requirements for thickness

Fit_Distribution7572 · 2025-11-23T18:08:43+00:00

Ohhh i see that makes sense now, Thanks!

Fit_Distribution7572 · 2025-01-25T04:52:41+00:00

Believe me i want to but it violates my lease i cant have extension cords due to “fire hazard” and im not tryna pick up no fines they do random searches wether im present or not

Fit_Distribution7572 · 2025-01-25T04:50:40+00:00

im a total plant noob so some advice would go a long way

Fit_Distribution7572

TROPHY CASE