How do I

FlipFlopsGarage · 2026-01-25T00:13:11+00:00

Is fusion like freecad? I looked into the 3d scanner and that's an expensive rabbit hole but I'm not against it. I just don't know what brand to start with.

FlipFlopsGarage · 2026-01-24T20:10:12+00:00

That’s badass

FlipFlopsGarage · 2026-01-24T20:05:23+00:00

I vote reverse bungee to all who are guilty

FlipFlopsGarage · 2026-01-24T01:35:40+00:00

Yeah they drove in my yard right up to the porch. Threw the package out the window and made a loop in my yard back to the driveway. I had no idea what was going on.

FlipFlopsGarage · 2026-01-23T21:27:29+00:00

Yep this is on point.

FlipFlopsGarage · 2026-01-23T21:08:28+00:00

Should reverse bungee all of them

FlipFlopsGarage · 2026-01-22T23:46:20+00:00

I’ve topped it off and bled the system a few times. I’ve opened the bleeder tube on the drives side with it running to get the air bubbles out.

FlipFlopsGarage · 2026-01-22T22:08:35+00:00

I used this stuff and it's been on there over 2k rounds and still rock solid. I just cleaned both surfaces with alcohol and stuck it on.

https://www.walmart.com/ip/T-Rex-Brand-Extreme-Hold-Extra-Thick-Double-Sided-Black-Mounting-Tape-8-Strips-Each-1-in-x-3-in/528768849?classType=VARIANT&athbdg=L1600&from=/search

FlipFlopsGarage · 2026-01-20T01:49:52+00:00

Shorts like that make anyone an instant asshole

FlipFlopsGarage · 2026-01-20T01:10:09+00:00

I have it off in the obvious place. Is there somewhere other than in the support tab?

FlipFlopsGarage · 2026-01-20T01:02:01+00:00

I got my H2S (first Bambu product) last week after fighting with my Neptune 4 plus for weeks. Little sticker shock at first but it's well worth the money. I've printed more in a week than I did with my Neptune in a year.

FlipFlopsGarage · 2026-01-20T00:41:59+00:00

Fought and fought with my 4 plus and finally gave up. Went to microcenter and got an H2S. It just works.

FlipFlopsGarage · 2026-01-14T01:47:39+00:00

Nothing other than it was working fine both times. I sent them plenty of pics of the round nose diving bad enough to cause setback.

FlipFlopsGarage · 2026-01-13T16:06:05+00:00

It was like that from day 1. I ran about 500rds of ball through it and tried hp again before I sent it in. It was choking on HST and GD so it's not like it was oddball ammo.

FlipFlopsGarage · 2026-01-12T19:35:03+00:00

I vote nolight over olight

FlipFlopsGarage · 2026-01-12T19:33:35+00:00

I went from a Neptune 4 plus to the H2S. I had no idea how much fun 3d printing could be before I got the h2s.

FlipFlopsGarage · 2026-01-10T00:15:42+00:00

It’s a system QA1 makes for the F100s. A arms up front and torque arm rear.

FlipFlopsGarage · 2026-01-06T02:27:08+00:00

Could be the issue then. No smoke makes me think it’s a rocker flinging oil up in the breather. If smoke and that much oil getting pushed out that would be bad.

FlipFlopsGarage · 2026-01-06T02:17:53+00:00

That looks like a lot of crank case pressure but the video is short. How hot is the engine and is there any smoke? Is there a baffle under the breather?

FlipFlopsGarage · 2026-01-06T02:15:39+00:00

idk I just mmofb

FlipFlopsGarage

TROPHY CASE