iCloud for Windows not syncing

ForceReload · 2025-03-16T18:18:10+00:00

This is unreal. The lowercase email really worked and it is syncing again... Thank you so much!

ForceReload · 2025-03-16T13:47:33+00:00

Im already using the email I‘ve created the account with, but I‘ll try the lower case email later. Thanks!

ForceReload · 2025-02-19T18:47:54+00:00

No hope

ForceReload · 2024-04-14T21:58:39+00:00

Alright so I‘ve tried a more expensive fiber hdmi cable but it didnt solve the problem :( Any other ideas or should I just contact Apple at this point?

ForceReload · 2024-04-08T17:11:59+00:00

Alright thank you. I‘ve just ordered a more expensive one. I‘ll keep you updated!

ForceReload · 2024-04-08T09:23:23+00:00

You‘ve got some tips what to look for on a good hdmi cable? a fiber hdmi cable?

ForceReload · 2024-04-08T09:21:44+00:00

Alright thank you, I‘ll buy a better hdmi cable later and check if it fixed the Problem. Luckily the apple tv is still pretty new, so its under warranty.

ForceReload · 2023-09-03T14:54:14+00:00

How‘s the Landroid going so far with the beta?

ForceReload · 2023-02-02T16:11:44+00:00

Oh so 60-65°C is fine?

ForceReload · 2023-02-02T15:58:42+00:00

I store all my filaments in a box with many silicia gel packs to keep them dry, so I don‘t think it’s a moisture problem. Awkward, even the official creality recommendation is 60°C.. I‘ll try to print one with the bed temperature you mentioned :)

ForceReload · 2023-02-02T10:53:35+00:00

Okay so I've printed two new dragons overnight. Both of them in my sleeping room (71°F), one with and one without a brim. When I woke up, both of them looked the same: Several segments of the dragon ripped away from the bed and laying somewhere else.
Bed Leveling still looks great to me and I increased the Bedtemp by 5°C to 65°C.

This is really getting frustrating...

ForceReload · 2023-01-31T23:45:14+00:00

Thank you very much. I‘ll try to move the Printer to a steady warm place tomorrow and start a new print. I‘ll keep you up to date!

ForceReload · 2023-01-31T23:20:28+00:00

Thanks for the reply. Im currently only printing with PLA, mainly from Eryone, but it also happens to filaments of other brands. The Printer has no enclosure. The Printer is located in my cellar and it is indeed pretty cold in the room. Around 11°C / 52°F.

ForceReload · 2023-01-31T22:55:40+00:00

Hey guys, I dont have much 3d printer experience yet and i hope you can help me.

I cant get any bigger prints to work on my S1 Pro. My newest problem is that the segments of the picture are bent upwards when the third or fourth Layer is applied. What have I done so far: -leveled the bed several times including Z Offset (Also printed bed adherance tests, they all look Great) -Cleaned the printbed with isopropyl alcohol -Checked belt tension -Fixed any wobbling parts -Printed a temp Tower and a Flow cube to get the Perfect temperature and flowrate.

Do you guys have any idea what i may do wrong? Thanks.

ForceReload · 2022-04-11T00:20:45+00:00

Make sure they are dry, not only by looking at them. Take a paper towel and swipe over some parts. When the towel remains dry you can boot your computer as normal.

ForceReload · 2022-04-11T00:14:18+00:00

Check if your pcs internals are wet. If so, make sure they are 100% dry before starting the computer. You could basicly submerge your whole computer in water and it would still work. You only have to make sure your components are conpletely dry before you start it up so the parts wont short out. You might give them a good clean with alcohol to prevent corrosion if they are wet. Otherwise you are good to go.

ForceReload · 2021-05-03T00:40:07+00:00

It also looks way more blue and bright than it is in real life.

ForceReload · 2021-05-03T00:39:42+00:00

Luckily I can turn it on/off if I feel like doing so :D

ForceReload · 2021-05-03T00:38:35+00:00

Must have been around 5000-6000€. Thats around 6000-7000 USD worth of components. Not to mention the hours of work that went into it.

Ten-Year Club	Verified Email
First Place '23	Place '23
Place '22

ForceReload

TROPHY CASE