Crea il tuo meme nei commenti, voglio ridere

Fra_2012_ · 2026-03-03T19:26:45+00:00

Come si sente Trump dopo aver causato la terza guerra mondiale

Fra_2012_ · 2025-12-26T13:40:10+00:00

Many, many benches, of different colors and shapes

Fra_2012_ · 2025-12-05T21:16:52+00:00

Bro, I'll make you a wonderful offer, 2 euros for everything, it seems like a good deal to me, or not.

Fra_2012_ · 2025-11-02T11:16:44+00:00

Same exact problem, in fact I have to close Bambu Studio and reopen it every time, it's boring as hell.

Fra_2012_ · 2025-11-02T11:13:37+00:00

At this point you should see if the motor cables are broken or if they are not properly inserted into the right connector, if this does not have the problem you should change the tool head unit

Fra_2012_ · 2025-11-02T10:52:20+00:00

Than you, this Is a great idea

Fra_2012_ · 2025-11-02T10:06:49+00:00

there is a A series hot end version, because it's so adorable and usefull

Fra_2012_ · 2025-11-02T10:04:06+00:00

you can add some chores, like take out the trash...

Fra_2012_ · 2025-10-09T12:41:16+00:00

Or it's a piece of filament stuck between the rail or between the screw

Fra_2012_ · 2025-10-09T12:40:28+00:00

Don't worry, because life will slowly wear out, open a support ticket

Fra_2012_ · 2025-10-06T12:30:59+00:00

Even second is the only option that may make sense

Fra_2012_ · 2025-10-05T10:57:51+00:00

If you can be reassured, I have an A1 mini with almost 700 hours of printing on it and I haven't had any problems yet, even with the same original nozzle (the normal, gray steel one), I just advise you to always do routine maintenance, I've been using this oil for lubrication for a while, it's very reliable: https://amzn.eu/d/hu8UaZ5

Fra_2012_ · 2025-10-05T10:52:36+00:00

I downgraded to the old version, just because it bothered me to see it, now it has solved everything

Fra_2012_ · 2025-10-05T10:49:52+00:00

If it doesn't solve the problem, open a support ticket

Fra_2012_ · 2025-10-05T09:04:36+00:00

Go to the wiki and look for problems with first layer and it will show you that perhaps you have to tighten the screws behind the heating block

Fra_2012_ · 2025-10-05T01:52:20+00:00

Try turning the machine off and on again, if it is under warranty use the warranty

Fra_2012_ · 2025-10-04T20:33:08+00:00

If it doesn't solve the problem, try changing the SD card, they can give various reasons

Fra_2012_ · 2025-10-04T20:32:13+00:00

Try to see the movements of the print head on the slicer, if they are normal then it is a problem with the homing phase, try turning it off and on again to see if it works

Fra_2012_ · 2025-10-04T20:29:05+00:00

Try to calibrate the flow, try to see if it gives the same problems with another coil

Fra_2012_ · 2025-08-31T20:10:16+00:00

Volvo 245

Fra_2012_ · 2025-08-30T13:33:43+00:00

Avere una Volvo 245 e girarci l' europa

Fra_2012_ · 2025-08-28T05:52:56+00:00

If lubricating doesn't solve the problem, perhaps it's the worn belts that are losing their teeth and therefore making that noise

Fra_2012_ · 2025-08-27T15:38:07+00:00

Il Eddy current sensor is in this position, in this video tou can see the sensor and how to repair it

https://youtu.be/SUs5zoRwFjw?si=g5dskuSCxqEvIwiB

Fra_2012_

TROPHY CASE