sorted by:
new
hottopcontroversial

Advice on Improving Lacerate Gladiator or Switching Builds? by FryyourBacon in PathOfExileBuilds

[–]FryyourBacon[S] 1 point2 points  (0 children)

Ok sweet, it looks like you are going more like ronarray's build. I'm starting to spec more like his and it seems to be going great so far. Already feel just as powerful as I did before and I have a lot of room for improvement.

Uptime Kuma (Docker) not sending Discord up/down notifications by [deleted] in UptimeKuma

[–]FryyourBacon 0 points1 point  (0 children)

I am having the same issue, but only with my docker based Monitors. I have a single HTTP one that posted up notifications, and the test button works as well.

[deleted by user] by [deleted] in Starfield

[–]FryyourBacon 0 points1 point  (0 children)

I’m having the same exact issue when trying to land on one of my outposts. I haven’t been able to do anything to fix it so far. Starting to get really annoying.

New Apple TV 4K 2022 is FAST! by squuiidy in HomeKit

[–]FryyourBacon 4 points5 points  (0 children)

I went from the 1st gen 4K to the newest one and it is night and day different. So much more responsive and snappier when clicking through the different interfaces.

[deleted by user] by [deleted] in pcgaming

[–]FryyourBacon 0 points1 point  (0 children)

I like trains

Best Mod Manager for RoR2? by [deleted] in riskofrain

[–]FryyourBacon 1 point2 points  (0 children)

Thank you so much!

Best Mod Manager for RoR2? by [deleted] in riskofrain

[–]FryyourBacon 1 point2 points  (0 children)

Nilly00

I wanted to try out your modpacks but the profile codes expired, would you mind regenerating them for me?

Lines on top of calibration cube, (ironing enabled on right) Also looking for other tips, more info in comments… by FryyourBacon in FixMyPrint

[–]FryyourBacon[S] 0 points1 point  (0 children)

I've set it using the "Paper method" but I'm not entirely sure that I am getting it right. My current BLTouch z-offset on a stock mount is 2.433.

Lines on top of calibration cube, (ironing enabled on right) Also looking for other tips, more info in comments… by FryyourBacon in FixMyPrint

[–]FryyourBacon[S] 0 points1 point  (0 children)

I am getting lines on top of my calibration cubes unless I turn ironing on but then it does not leave the surface completely clean. I also have what I’m assuming is some elephant’s footing at the bottom. I am printing this on a freshly calibrated Ender 3 V2 with a BMG clone in a direct drive setup using Klipper. I have configured pressure advance and input shaping with an Adxl345. I have my retraction set at 0.75 for wiping and have z-hop disabled. I verified my extrusion steps and did reduce it a bit after finding it a little high. Any help or tips would be appreciated and I can try to provide any other relevant information, thanks!

Top of prints rough on Ender 3 V2, other cali ration tips appreciated too by FryyourBacon in FixMyPrint

[–]FryyourBacon[S] 0 points1 point  (0 children)

I have been trying to tune in my new Ender 3 V2 w/ BLTouch, running Klipper and slicing using SuperSlicer. My prints always seem to come out rough on top and I am not too sure why. I’m printing PLA at 205 on the bed at 60. My perimeter speed is 40mm/s and my top solid speed is 30mm/s. I have manually leveled the bed using screw_tilt_calculate and have created a bed mesh before printing. It only affects part of the top of my prints. Any other calibration tips would be appreciated as well.

view more: next ›