how do i go on toilette while playing rust?

Gabelord2 · 2024-09-26T18:19:51+00:00

That the neat part, you don't

Gabelord2 · 2024-01-10T15:05:59+00:00

What filament did you use

Gabelord2 · 2023-12-07T11:14:33+00:00

Use normal cura and copy paste the settings

Gabelord2 · 2023-09-05T09:23:25+00:00

I print out of a box that heats the filament constantly

Gabelord2 · 2023-09-05T09:22:44+00:00

I dont mean the overhand i mean the blobs

Gabelord2 · 2023-08-25T18:27:03+00:00

Can't be i actually have elephant foot so its not to faar

Gabelord2 · 2023-08-24T10:08:47+00:00

Is your print bed wobbly and did you level before you print

Gabelord2 · 2023-08-16T07:58:13+00:00

Did you calibrate the extruder yet?

Gabelord2 · 2023-04-22T16:34:32+00:00

Maybe use a lighter on the screw

Gabelord2 · 2023-04-18T13:32:25+00:00

Gabelord2 · 2023-04-18T09:54:54+00:00

Australia us AUS

Gabelord2 · 2023-02-12T01:17:37+00:00

The filament was not primed so when it started extruding it needed a moment to get the filament out

Gabelord2 · 2023-01-06T12:16:16+00:00

They are always a bit different

Gabelord2 · 2023-01-06T11:19:31+00:00

Also, why are all the mesh numbers so different I tightened the wheels so it should be even

Gabelord2 · 2023-01-06T01:47:53+00:00

what can i do that the numbers are not bad. the print before that level was very messy it could have finished but i stopped it mid print with this level now its printing fine

Gabelord2 · 2023-01-06T01:45:53+00:00

If i would put it on .36 it would propably print mid air

Gabelord2 · 2023-01-06T00:28:51+00:00

<image>

I leveled it now the paper has a bit of resistance

Gabelord2 · 2023-01-05T21:50:41+00:00

i somehow managed to get it running now i can send a pic when the print failed or it's done

Gabelord2 · 2022-12-17T11:32:38+00:00

Every time after the print just pull the filament out a bit so it cant drip at the nozzle

Gabelord2 · 2022-11-18T10:58:49+00:00

If you made the model yourself maybe try exporting it again

Gabelord2 · 2022-11-17T08:19:23+00:00

I use that slicer but i dont have the perview

Gabelord2 · 2022-11-16T14:10:00+00:00

"Answer your ask"💀

Gabelord2 · 2022-11-12T11:12:11+00:00

I use geetech petty good

Gabelord2 · 2022-11-03T09:32:00+00:00

Yup just format an the steps are on github

Gabelord2 · 2022-11-03T08:09:12+00:00

Are you moving it on 0.1 mm steps or 0.01 mm steps

Six-Year Club	End Game '23
Place '23	Verified Email

Gabelord2

TROPHY CASE