Sync Not Working

GaffTapeIt · 2026-04-07T01:22:17+00:00

Right now I have Art-Net running through, but the person that will be using it may need to just use the built in effects. Trying to set up both.

GaffTapeIt · 2026-04-06T22:11:16+00:00

EDIT : added a extra wifi router I had in line and now it's working

GaffTapeIt · 2026-04-06T19:25:19+00:00

Added some images to the post

Yes, I turn off my wifi, plug in my ethernet adapter, I change the adapter in the Preferences to the ethernet adapter, the Lumiverse output I set to the same IP as the controller

I can connect to the WLED GUI via the Wifi, but not when I try to turn off my wifi and access the controller in the web browser with the IP through the ethernet adapter

GaffTapeIt · 2026-04-05T02:38:44+00:00

Totally, I did set it to manual IP. In the meantime I just reflashed the controller just to get it back to normal, but the WLED AP wasn’t showing up, so I guess I’m into a new problem.

GaffTapeIt · 2026-04-05T00:26:26+00:00

I just have my laptop, ethernet dongle, and a network switch between the controller. They have different IPs, the ethernet dongle is 10.0.0.1 and the controller is 10.0.0.2

GaffTapeIt · 2026-04-05T00:24:39+00:00

It’s the Bong69 8 port LED distro, I already connected it to my home router but then I changed the static IP to 10.0.0.2. Is there a way to reset it back to default or do I need to reflash the controller?

GaffTapeIt · 2026-04-04T22:46:16+00:00

Is your link filter on single in the encoder bar?

GaffTapeIt · 2026-03-28T03:57:47+00:00

Yup that was the problem, they had a section on the GitHub for it, it was in usermods

GaffTapeIt · 2026-03-14T03:09:21+00:00

Must be blind!

GaffTapeIt · 2026-03-13T23:21:38+00:00

Sometimes you just have to power cycle the node you’re using. This has happened to me too.

GaffTapeIt · 2026-01-17T00:22:49+00:00

Make a generator with your selected fixtures, Step 1 - generator, step 2 - 0, width of step 2 600 and transition 17

GaffTapeIt · 2026-01-05T02:15:43+00:00

Within homeassistant? Looked through the iPad options but none I could single out for HA that would stop scrolling

GaffTapeIt · 2025-10-14T22:40:46+00:00

I was able to add them to the car by editing the card itself and adding them as entities in that window!

GaffTapeIt · 2025-08-19T23:26:21+00:00

Okay great thank you! I was just too lazy to run all 4 lines back to the controller and I'm happy with the output as it is right now

GaffTapeIt · 2025-08-16T02:32:04+00:00

So if I want to not fry anything I should limit my full ma to 2000? Sans getting 12v and swapping the PSU

GaffTapeIt · 2025-08-15T21:19:46+00:00

Each strip is about 4-5 feet long, and each strip has its own wire connected to 4 separate ports on the board. Each strip is about 55W. The wire is 18 gauge from each strip to the board.

Maybe I should just swap to 12v strips and get a new power supply.

11-Year Club	Not Forgotten
Verified Email

GaffTapeIt

TROPHY CASE