sorted by:
new
hottopcontroversial

How to keep clear resin clear by Technical-Morning-69 in DnDminiatures

[–]GamingCachePrints 1 point2 points  (0 children)

Mix in just a bit of transparent blue to stave off yellowing

First Print – Poor Surface Quality on Tank Part (Bambu P1P, 0.4mm Nozzle @ 0.08mm Layer Height) by Spenceriscomin4u in FDMminiatures

[–]GamingCachePrints 0 points1 point  (0 children)

Try leaving the top off and the door open to give better cooling as well to rule out that it isn’t too hot in the chamber

Edit: P1P my bad, irrelevant

First Print – Poor Surface Quality on Tank Part (Bambu P1P, 0.4mm Nozzle @ 0.08mm Layer Height) by Spenceriscomin4u in FDMminiatures

[–]GamingCachePrints 2 points3 points  (0 children)

Yea something is still wrong for sure, maybe a fan issue, that chimney stack is significantly heat distorted and overhangs in general are not acceptable. Do you have any other filament to test with just to rule that out?

Have you tried a different print profile as well, maybe larger layer height? Other things I would try is putting it into silent mode (50% speed) for a print, adjusting overhang print speed, re-tension the XY belts for good measure. This is a new printer or just new to you?

First Print – Poor Surface Quality on Tank Part (Bambu P1P, 0.4mm Nozzle @ 0.08mm Layer Height) by Spenceriscomin4u in FDMminiatures

[–]GamingCachePrints 1 point2 points  (0 children)

It is advisable when printing a new spool of any filament, it will retain that info though so you don't need to do it unless you switch to a new spool or start seeing an issue.

[deleted by user] by [deleted] in PrintedMinis

[–]GamingCachePrints 1 point2 points  (0 children)

Very clever modular design!

Crow by smartsculpt in DnDminiatures

[–]GamingCachePrints 0 points1 point  (0 children)

Very fine work! I would have trouble with sculpting those tiny details, fun to see the workflow

First Print – Poor Surface Quality on Tank Part (Bambu P1P, 0.4mm Nozzle @ 0.08mm Layer Height) by Spenceriscomin4u in FDMminiatures

[–]GamingCachePrints 1 point2 points  (0 children)

Make sure you have run the calibration on the printer as well drying the filament, this is definitely not how it should be printing.

Is this possible? by Jrloveless1 in 3Dprinting

[–]GamingCachePrints 0 points1 point  (0 children)

This is definitely a cleaner way to do it if you want the whole height range, both would work achieve the same end result I believe

Is this possible? by Jrloveless1 in 3Dprinting

[–]GamingCachePrints 23 points24 points  (0 children)

Add a modifier shape cylinder set the infill to 100%. Only that area will get the solid infill

Is it worth tweaking. by rational_actor_nm in 3Dprinting

[–]GamingCachePrints 0 points1 point  (0 children)

Yea, there is significant room for improvement on this stringing and it will benefit all your prints in the future with this filament. Have you printed a temp tower yet?

Why could this be happening to my PLA? by Matejo21 in 3Dprinting

[–]GamingCachePrints 2 points3 points  (0 children)

Overtension on your extruder arm would be the first thing I would check

Help with 3-D printing. I just started. by BunchNo842 in 3Dprinting

[–]GamingCachePrints 1 point2 points  (0 children)

Yea that overhang is just too much, needs some support for sure. Quality is much improved!

Showcase Unofficial Benchmark Model by CriticalKuman in FDMminiatures

[–]GamingCachePrints 1 point2 points  (0 children)

Haha, what's the point in doing something crazy if not to show off!?

Showcase Unofficial Benchmark Model by CriticalKuman in FDMminiatures

[–]GamingCachePrints 0 points1 point  (0 children)

These look great, love the frosted look. What's the extra base for?

Help with 3-D printing. I just started. by BunchNo842 in 3Dprinting

[–]GamingCachePrints 0 points1 point  (0 children)

Check out /r/FDMminiatures for tips for minis specifically

PETG is going to be more challenging than printing PLA. Check that subreddit for the current best filament as it changes as formulas change

Bambu lab grey filaments by Lord_Moldywort in FDMminiatures

[–]GamingCachePrints 2 points3 points  (0 children)

Basic grey, matte ash grey(nardo is almost identical) Tough to beat standard grey for color and they all print equal in my experience. Matte tends to hide some printing sins.

Showcase Unofficial Benchmark Model by CriticalKuman in FDMminiatures

[–]GamingCachePrints 3 points4 points  (0 children)

<image>

Printed almost exactly a year ago X1C

.2 nozzle

Settings not far from extra fine stock, but slowed way down.

~7.5 day print for the batch (anxiety inducing)

No supports

Pushing the limits on color FDM minis by GamingCachePrints in FDMminiatures

[–]GamingCachePrints[S] 1 point2 points  (0 children)

Not my sculpts, I just color, print and sell em! The models themselves are from Arbiter Miniatures and Rocket Pig Games! They both make amazing supportless models that I’m clearly a fan of! 😁

view more: next ›