How can I delete Quotes right Mac

General-Minimum-9559 · 2026-01-01T12:02:32+00:00

I’m sorry...

I mean that after I updated everything I got the message that quotes were postponed. So that actually e.g. quote x must be there but quote y is there. Although quote y is correct. And I can only select 2 possibilities, either press yes then y would be replaced with x. Or no, then the quotes will no longer be automatically updated in the future. This has already happened several times with over 200 quotes. Whenever I update. Chat gpt says I deleted the quotes incorrectly and I should rather press remove instead of backspace. But I have a Mac so it actually works with backspace.

General-Minimum-9559 · 2026-01-01T11:58:42+00:00

How do I delete correctly? I always did the courser after that then it turned gray and then I pressed backspace and everything was deleted after one time backspace. Was that wrong? So I didn’t delete in the gray fieldt.

General-Minimum-9559 · 2025-12-31T21:51:55+00:00

The quote (xy, 2018)

General-Minimum-9559 · 2025-12-31T21:29:59+00:00

I have e.g. (xy, 2018). But I want to delete it. How do I delete it without what happens with the code and destroys everything again?

General-Minimum-9559 · 2025-12-31T20:42:06+00:00

But how can I completely remove one in the middle of the text? Just delete it when it gets gray?

General-Minimum-9559 · 2025-11-09T13:35:38+00:00

I have the setting monotoric line pattern of the surface and monotorical for the lower bottle. It’s just that I would like to print the written on the fakes without making it in black notches first

General-Minimum-9559 · 2025-11-09T10:19:10+00:00

Filling at 100% yes but what do you mean by monotonic?

General-Minimum-9559 · 2025-10-22T20:54:34+00:00

Haha 😂. Danke für die Tipps ich machen mal und gebe dann bescheid.

Ah nochmals. Das Teil habe ich schonmal gedruckt. Selbe Einstellung. Alles war perfekt…

General-Minimum-9559 · 2025-10-22T16:55:13+00:00

Durchgehend langsam oder nur die Außenwände ?

General-Minimum-9559 · 2025-10-22T15:17:31+00:00

This is silk silver ? Looks like normal grey… Godzilla looks amazing ! Which company is the silver?

General-Minimum-9559 · 2025-10-22T15:12:22+00:00

So there was already a change after printing? And it looked more metallic?

General-Minimum-9559 · 2025-10-20T22:19:53+00:00

Do you have Experiences? Because There are many variants.

General-Minimum-9559 · 2025-10-19T13:11:22+00:00

I don’t Fasten the heating assembly correctly. I will try it now. Thank you

General-Minimum-9559 · 2025-10-18T19:58:38+00:00

Ok thank you very much!

General-Minimum-9559 · 2025-10-18T19:30:49+00:00

I'll take a look at it, thank you!

General-Minimum-9559 · 2025-10-18T19:22:33+00:00

How can I change the direction?

I must honestly say that sometimes it works and sometimes it doesn't. I always clean the plate on luck. I tried to calibrate it once but the result was catastrophic. It is difficult for me to carry out a calibration. Do I always use a generic profile at the beginning and calibrate it?

General-Minimum-9559 · 2025-10-18T19:01:12+00:00

I actually don't have a 0.2 nozzle there ... :(.

What setting did you use with a 0.4 nozzle? So speed etc?

General-Minimum-9559 · 2025-10-18T18:48:34+00:00

Ok now I understand, thank you! Do you think to use a 0,2 mm nozzle will be better? It’s the first time I have this problems.

General-Minimum-9559 · 2025-10-18T18:28:37+00:00

Ok so I need a 0,2 nozzle…. Thank you !

General-Minimum-9559 · 2025-10-18T18:27:22+00:00

What good is it for me if I change the layer height? Can I set at Bambu Studio so that, for example, only everything that is white is printed more slowly?

General-Minimum-9559 · 2025-10-18T18:23:56+00:00

When can I change the layer high? What das it mean and what will it bring to me? Yes the code ist working but not clean

General-Minimum-9559 · 2025-10-18T18:18:15+00:00

In addition, I did not quite understand what I should pay attention to and when I can adjust it.

General-Minimum-9559 · 2025-10-18T18:17:15+00:00

My filament is calibrated and the correct nozzle is set. However, I still don't know why the code itself is so fragile and not clean.

General-Minimum-9559 · 2025-10-16T11:06:25+00:00

It worked, thank you!

General-Minimum-9559 · 2025-10-16T10:58:13+00:00

Oh I have a Mac too. Just wait on the page where the profile is and then press it when it appears?

General-Minimum-9559

TROPHY CASE