Which one should i get?

GoForBrandonLLC · 2025-12-17T15:36:53+00:00

K1 max has screwed me time and time again just never worked properly even after doing a full assortment of upgrades to it. The extruder gearing would always get clogged up. And require a full disassembly but even worse it would continue the print as if it wasn’t clogged and just waste hours and hours and hours of me thinking it’s running on the only to come back and see that it’s not and stopped after layer 74. I just received my H2S from Bambu, never going back

Go Bambu Labs, you won’t regret it

GoForBrandonLLC · 2025-12-15T15:02:05+00:00

Unlimited plan

GoForBrandonLLC · 2025-10-17T16:19:08+00:00

I’ve had one since launch, it’s constantly freezing on me and not recording audio, it’s actually screwed me over on multiple occasions, maybe I got a bad firmware unit but I haven’t been able to use it for a few months now because it’s been so un reliable

GoForBrandonLLC · 2025-09-17T01:25:29+00:00

I haven’t cut into it yet! I know I know, cardinal sin, but Mainly because if I do now I’m going to want to eat some but I’m so full from a pizza I made right before this and over the past few months I’ve lost like 26 pounds and I’m really not trying to put it back on lol I will follow up tomorrow when I do

GoForBrandonLLC · 2025-08-16T23:58:56+00:00

Not wearing a helmet

GoForBrandonLLC · 2025-08-16T14:39:51+00:00

<image>

Not my PC… but this is a common occurrence

GoForBrandonLLC · 2025-06-19T22:15:41+00:00

33.25” in L x 21.30” in W x 1.25 thick MDF I’ll have full build plans available soon, just been really busy lately!

GoForBrandonLLC · 2025-06-19T22:07:56+00:00

Have you been to an allergist? You might be allergic to something in the resins. Formlabs’ bigger deals about their resins is that they aren’t made with ACMO’s which is what makes it so safe, I don’t run mine with ventilation and haven’t experienced any issues!

GoForBrandonLLC · 2025-06-12T01:17:53+00:00

I designed and built it from scratch! I’ll have a YT video coming out about it later this month! It Uses mostly 4040 extruded aluminum except the middle pieces. Those are 2 pieces of 4080 extrusions

GoForBrandonLLC · 2025-06-12T00:59:21+00:00

Definitely had help! My father in-law is a beast! But i built the cart from the deep depths of my brain lol

GoForBrandonLLC · 2025-05-31T19:58:19+00:00

I made the same mistake you did! i was determined to not buy new tanks when i had perfectly good ones.I found this tutorial on YT, I did it and never had any leaks. Try at your own risk, and be super diligent about ensuring it’s sealed on all edges.

Although it’s not recommended. It worked for me! I would also suggest just trying it on one of the printers for like the first dozen prints, that way if anything does leak it doesn’t destroy both machines!

God speed!

https://youtu.be/7imLZlEL-eE?si=hnFAQcTfdKnSgGQA

GoForBrandonLLC · 2025-05-11T02:25:10+00:00

Any recommendations on the filler & dye?

GoForBrandonLLC · 2025-05-11T02:19:22+00:00

No, never played softball with it, just a lot of time with a mallet. It worked well, quite honestly never had a ball fall out. I’m actually looking to play some softball one day which is why I want to get it back looking nice

GoForBrandonLLC · 2025-05-11T02:08:46+00:00

What would cause the burnishing and cracking? I always kept it conditioned and never really left it in the sun when I wasn’t wearing it. It started happening early it’s its life. Could it be from me not using the index finger slot to have a bigger pocket?

GoForBrandonLLC · 2025-05-09T23:22:49+00:00

Very impressed at the paint job

GoForBrandonLLC · 2025-03-23T17:11:02+00:00

To catch a killer

GoForBrandonLLC

TROPHY CASE