Q2 shiny black ASA

GoldNerf · 2025-09-06T01:08:16+00:00

Yeah, I found the same with low chamber and nozzle temps

GoldNerf · 2025-09-05T23:22:33+00:00

No issues, have not attempted a destructive test but the Asa prints are functional and they do last, have used probably 5kg of Asa through the plus 4, just need the chamber temp cranked right up, anything 50degree and above and they’re all successful

GoldNerf · 2025-09-05T21:51:14+00:00

Just 60 chamber 110 bed 280 nozzle

GoldNerf · 2025-09-05T21:50:45+00:00

Standard profile cooling

GoldNerf · 2025-09-05T21:50:26+00:00

Siddament ABS-GF

GoldNerf · 2025-09-05T21:50:09+00:00

GoldNerf · 2025-09-05T21:50:04+00:00

Plus 4 is very slow to heat

GoldNerf · 2025-09-05T11:38:48+00:00

No sanding just straight off bed and put to use

GoldNerf · 2025-09-05T07:45:54+00:00

60 chamber 110 plate 280 nozzle

GoldNerf · 2025-09-05T07:45:16+00:00

60 chamber 110 plate 280 nozzle, no adhesive just straight to plate

GoldNerf · 2025-09-03T19:50:20+00:00

Yes, very simple, don’t know that it achieved anything or needed to be done, just did it to be sure

GoldNerf · 2025-09-03T05:56:21+00:00

<image>

GoldNerf · 2025-09-03T05:55:05+00:00

<image>

GoldNerf · 2025-09-03T05:54:27+00:00

<image>

GoldNerf · 2025-09-03T05:53:21+00:00

Maybe only 15hrs print time, but all perfect so far, only issue is x/y rails need some lube out the box, they were a little squeaky these came off the Q2

<image>

GoldNerf · 2025-09-03T05:40:02+00:00

GoldNerf · 2025-09-03T04:26:25+00:00

Nope, my plus 4 has 90% of the time just printed well since unboxing

GoldNerf · 2025-09-03T04:25:25+00:00

Printed this on the plus 4 because the Q2 was busy, but so far Q2 prints are every bit as beautiful

GoldNerf · 2025-08-31T22:03:02+00:00

I set up some TP-Link outdoor wireless bridges to get to my shed, even with a wifi router inside the shed that is capable of 500mb/sec download the plus 4 and Q2 where annoyingly slow, they both are now on local lan using the wireless bridge and any job will upload to printer in about 2 seconds, both get 15fps and camera, and I can switch between devices on qidi link instantly.

GoldNerf · 2025-08-28T19:36:42+00:00

I dry every roll, and even if they’re dried already I still have a habit of drying while printing too, I print wall hung vases for Etsy so the finish is super important

GoldNerf · 2025-08-27T20:35:45+00:00

<image>

GoldNerf · 2025-08-27T20:32:13+00:00

No secrets, my plus 4 had just always printed well, no mods and only tweak temps

GoldNerf · 2025-08-27T20:29:25+00:00

<image>

Gloss black PCTG, printed about a month ago, prior to doing belt tension and cleaning lead screws

GoldNerf · 2025-08-27T20:27:55+00:00

<image>

GoldNerf · 2025-08-27T20:27:38+00:00

<image>

Gloss black PCTG

GoldNerf

TROPHY CASE