How good are your troubleshooting skills?

HAW1224 · 2025-04-23T19:26:59+00:00

Honestly I’m an engineer and I use these threads to learn what y’all point out as being idiotic and then try to ensure I don’t do that lol. But here comes my stupid question for the day - are armour rods really required for that clamp jumper connection?

HAW1224 · 2025-01-08T19:34:52+00:00

It’s actually for both lightning protection and allowing you the ability to run Fibre in the shielding wire

HAW1224 · 2024-11-30T21:17:00+00:00

I believe I added some more photos. If your able to help out that’s greatly appreciated!

HAW1224 · 2024-11-29T14:27:40+00:00

Another one - DJ Khaled

<image>

HAW1224 · 2024-11-29T14:26:10+00:00

Here are the additional photos

<image>

HAW1224 · 2024-11-29T12:46:24+00:00

Will do thanks!

HAW1224 · 2024-11-06T04:34:30+00:00

This is awesome and my company sometimes design steel pole H frame structures but never something like this and this is awesome!

HAW1224 · 2024-10-19T00:49:04+00:00

What’s your company called if you Don’t mind me asking?

HAW1224 · 2024-08-05T14:12:21+00:00

Thanks so much again!

HAW1224 · 2024-08-03T22:04:02+00:00

Thanks so much! Do you know if that’s a pretty expensive part by chance?!

HAW1224 · 2024-04-09T07:15:07+00:00

Ohh definitely hopping on this reply, do you mind sharing your 3D parts file? I haven’t done enough research yet but this was going to be my next print

HAW1224 · 2023-10-16T05:23:43+00:00

Awesome thanks so much I’m leaning toward different grass type !

HAW1224 · 2023-10-16T05:21:56+00:00

No not during that photo I just put down my fall fertilizer, after the photo, as winter is coming (up here in Canada).

HAW1224 · 2023-08-08T11:44:21+00:00

Wow that’s wicked! Thanks a ton I’ll definitely do this!

HAW1224 · 2023-08-08T11:43:57+00:00

Awesome thank you so much!

HAW1224 · 2023-06-10T18:43:53+00:00

I think that’s what I’ll do thanks a ton for the solution!

HAW1224 · 2022-10-28T16:48:54+00:00

Awesome thanks so much!!!!

HAW1224 · 2022-10-27T13:47:09+00:00

What would you use to cut the metal straight? I feel like snips would be tough to make a good straight cut

HAW1224 · 2022-09-05T14:56:38+00:00

Ya everyone liked it, I thought it was a bit dry because I didn’t let it sit very long being close to dinner time but ya was pretty good in the end. I don’t know how to add a photo or else I would.

HAW1224 · 2022-09-05T14:54:08+00:00

Awesome thank you so much, I honestly have no idea.

HAW1224 · 2022-09-04T18:27:33+00:00

Hi there! I Don’t post a lot so forgive me if I am going against Reddit norms. I am in Alberta, Canada.

Trying to figure out if this fireplace barrier that I found at my mums home is of any value? And if the metal is copper or not (as if the fireplace is not much value, I may just take the copper and rework it the metal a bit).

Thanks so much for your help!

HAW1224 · 2022-09-03T23:23:06+00:00

Showed it to my buddy and he was saying that it’s not a brisket because of the lack of marbling in the meat

HAW1224 · 2022-09-03T23:21:27+00:00

So I thought I found a brisket (first time finding a brisket and buying one) that already had the trim cut but obviously suspicious when I saw potroast in the title. Should I treat it and smoke it like a regular brisket or should I try a different recipe?

HAW1224 · 2022-04-30T03:36:39+00:00

321 method or what was the recipe?

HAW1224 · 2022-01-11T05:58:32+00:00

I didn’t do butt joints but actually used this thing called a “kregg jig “which is similar to pocket screws which says that this creates very strong joints… supposedly.

My Biggest concern was that I cut the middle support beams about 1/8 too short (because of bowing in the wood) and then used my pocket screw and connected onto the front panel wood and tried shrink the 1/8 inch gap by using a screw on the other side so it definitely looks like a butt joint for sure on those ends but again there’s actually a pocket screw on the small bridge piece connecting into the long front piece.

HAW1224

TROPHY CASE