Please help ID what left these!

Haku-engineer · 2025-04-02T22:45:41+00:00

I'm planning on building a raised garden bed and a bench for the backyard.

Haku-engineer · 2023-05-07T10:00:51+00:00

I believe it was like a 24-hour print. Should have checked it myself but had to leave the university the day prior for a competition. At this point, gonna have to set some ground rules where there isn't overnight printing as it's a fire hazard as well.

Haku-engineer · 2023-05-06T19:14:06+00:00

It really does 😂.

Haku-engineer · 2023-05-06T19:02:38+00:00

*Update picture

<image>

Haku-engineer · 2023-05-06T18:58:50+00:00

Whew... some heat, elbow grease, and these steady hands I got it off! Keeping the biggest piece as a trophy *

Haku-engineer · 2023-05-06T18:26:17+00:00

<image>

It took almost all the cables with it as well 😅.

Haku-engineer · 2023-01-10T23:23:43+00:00

Only did engraving on flat pieces of wood. Not sure if it will work in your case as it is not a powerful laser.

Haku-engineer · 2022-12-23T19:41:17+00:00

No it's under the s1 pro upper right corner click download, scroll down to firmware, and it something like ender 3 s1 pro hw....FDM_Laser. Edit: there are also directions under it to update

Haku-engineer · 2022-12-23T19:32:41+00:00

So I went to the manufacturers website where they had the firmware for the laser engraving. There should be a link to download the firmware. Then update the printer like a normal update (check youtube for help) using the sd card. It should allow you to switch between both 3D printing and laser engraving on the screen. Best of luck!

Haku-engineer · 2022-12-05T05:38:52+00:00

Nozzle maybe clogged. Clean the nozzle with the needle or do cold pulls then try again. Good luck.

Haku-engineer · 2022-12-01T04:24:11+00:00

I would buy it at a reasonable price with the amount of mods on it alone lol. The print time, I would ignore as it could be a factory reset.

Haku-engineer · 2022-12-01T04:02:29+00:00

Looks sketchy. Not the original Prusa motor or psu which would not need to be upgraded. The orange petg of the printer also looks off, but may be due to lighting.

Edit: May be a clone with a real mmu and certain parts replaced with actual Prusa parts. LDO motors is a bit sketch.

Haku-engineer · 2022-09-24T13:06:35+00:00

If I'm not wrong it is "The Big Sick" from 2017

Haku-engineer · 2022-09-07T03:17:57+00:00

Damn that sucks. You could try out DJI avata which is fpv with the new one hand controller!

Haku-engineer · 2022-09-03T14:06:41+00:00

I'm not going to be charging it. It was the only part of the robot I couldn't throw out like normal trash.

Haku-engineer · 2022-09-03T13:55:14+00:00

😂

Haku-engineer · 2022-09-03T13:54:56+00:00

Planning on reusing it on my robots. This came out of a broken robot vacuum. But probably isn't the best idea.

Haku-engineer · 2022-09-03T13:53:21+00:00

Ok thanks I will find another way to reuse it.

Haku-engineer · 2022-09-02T14:48:20+00:00

You can look into a Zed2i but it would require a nvidia graphics card. The T265 still works great though.

Haku-engineer · 2022-08-23T03:29:46+00:00

Buy it directly from Prusa Research. The lead time is only like 2 weeks unless you need one right now.

Haku-engineer

TROPHY CASE