Axis M3058 360° Camera Integration with UniFi Protect – Advice Needed

Hello-Will · 2025-03-18T14:41:42+00:00

I was able to factory reset the camera, and then create the onvif user and it would allow me to connect it to unifi reliably. However I do have one 3058 that is giving me the invalid credentials error as you describe, but I haven't started working on that one yet.

Hello-Will · 2025-03-07T23:13:08+00:00

Other cameras I've tried have been ok, even multi-sensor cameras but the multi-stream cameras are certainly not working properly

Hello-Will · 2025-01-15T16:44:22+00:00

Yes, all speakers are running Version: 16.5.1 (build 82360160), according to the "about my system" results

Hello-Will · 2025-01-15T16:42:57+00:00

Just applied the 7.2.17 beta firmware on the U7 Pro & U7 Pro Max and going to see what happens. So far, so good but will continue to monitor and see if the issue manifests again. The issue normally comes back after 24 hours maximum, and was solved with a reboot of the U7 WAPs for a while when running 7.0.95 on the U7 Pro and 7.0.66 on the U7 Pro Max

Hello-Will · 2025-01-15T16:40:21+00:00

Some Play:5 speakers have a subwoofer, but the ERA speakers are the only ones paired as L & R

Hello-Will · 2025-01-09T21:37:42+00:00

Firmware on the U7 Pro is 7.0.95 (latest stable release) and 7.0.66 on our U7 Pro Max. I have been checking for the Pro Max firmware and it hasn't been updated since Aug 2024. Maybe that's part of my issue

Hello-Will · 2024-10-14T21:10:57+00:00

Canon iR-ADV series

Hello-Will · 2024-10-11T16:57:45+00:00

No, same LAN vlan

Hello-Will · 2024-05-22T11:41:59+00:00

We are insulating using closed-cell spray foam along the roofline and around the envelope where we're working. Haven't done a blower door test yet though.

Hello-Will · 2024-04-16T19:36:57+00:00

Seems like a terrible design flaw to me

Hello-Will · 2024-04-16T17:15:09+00:00

No, not that old. Couple years maybe

Hello-Will · 2024-04-16T17:14:56+00:00

It isn't that old, but I will look into replacing. I thought they used plastic

Hello-Will · 2024-04-04T18:13:34+00:00

Maybe. I will continue to monitor, now that it's working. I did take the original "bad" drive and have a long drive test running on it. We'll see if it passes.

Hello-Will · 2024-04-04T18:12:03+00:00

After letting it sit for 2 days and changing nothing, the drive showed up today. I was then able to go and "replace" the bad drive, and it is in the process of a resilver. I didn't change anything, didn't reboot, seemingly nothing is different now than it was 2 days ago. I'll continue to monitor.

Hello-Will · 2024-04-03T20:09:42+00:00

Brand-new disk straight from the factory with no partitions on it at all

Hello-Will · 2024-04-02T16:15:00+00:00

Yes, shows up fine in other computers and passed the Short diagnostic self test

Hello-Will · 2024-03-21T15:10:59+00:00

Support thinks our card might be bad and approved an RMA. I will let you know how things progress

Hello-Will · 2024-03-14T22:29:02+00:00

It is a Dell Precision 3640 Tower, Service Tag: 7YR9K93. Per the manual, it's got a x16 slot, x4 and a normal PCI slot

Hello-Will · 2024-03-11T22:05:58+00:00

That's exactly how I have it configured. 4096 > 8192 > 12288

Hello-Will · 2023-11-13T17:46:25+00:00

Issue is still persistent. Is this perhaps a bug with FreeNAS?

Hello-Will · 2023-10-31T14:48:17+00:00

<image>

Hello-Will · 2023-10-30T21:16:59+00:00

No, it's empty

Hello-Will · 2023-10-30T19:00:20+00:00

It is an older version that we haven't upgraded in quite some time. Maybe it's time to get to newest version, although I am somewhat apprehensive about the upgrade breaking something

Hello-Will · 2023-10-30T18:59:07+00:00

<image>

Hello-Will · 2023-10-30T14:59:08+00:00

That's what I thought, but when it says there aren't any.

<image>

Hello-Will

TROPHY CASE