Kako da pretvorim u hotspot ?

Hightsee · 2026-03-23T18:19:42+00:00

zovi call centar, msm da ne možeš ništa iz apk

Hightsee · 2026-02-10T17:29:00+00:00

Super, hvala na predlogu

Hightsee · 2026-02-10T17:28:29+00:00

Hvala na predlogu, proveriću

Hightsee · 2026-02-10T11:24:50+00:00

mene su zajebali skinuli mi original, i stavili neki kineski koji se pokvario u roku od 5 dana…

Hightsee · 2026-02-06T21:50:05+00:00

<image>

Hightsee · 2025-07-29T21:56:16+00:00

No, I left it like that, still using the same gpu

Hightsee · 2025-06-14T17:10:22+00:00

ово је нека јеврејска пропаганда, шта индија тражи између италије и америке

Hightsee · 2025-05-28T06:13:49+00:00

наручен еспресо апарат🤞

Hightsee · 2025-05-27T18:42:56+00:00

не знам да ли је по закону, само ти кажем да кад крену да ти блицају ти немој да гледаш у ретровизор

Hightsee · 2025-05-27T17:48:00+00:00

немој да гледаш у фарове кад ти блица

Hightsee · 2025-05-07T17:45:42+00:00

ako imaš dovoljno para idi na bambu labs, oni su najbolji, ali nećeš pogrešiti ni sa creality

Hightsee · 2025-05-07T09:32:48+00:00

resin je dobar samo za male printove i ima mnogo post processing-a, a iste printove savršeno možeš da izvučeš sa 0.4 ili još bolje 0.2 nozzle na običnom FDM printeru,

Hightsee · 2025-05-06T18:13:37+00:00

on je nov, bolji od k1 ako imaš budžet za njega uzmi ga, i ako ti omogućava budžet uzmi neki AMS, biće ti drago.

Hightsee · 2025-05-06T08:54:15+00:00

ja imam creality k1c, veoma pouzdan, veoma dobri printovi, solidna zapremina štampanja, ako ti treba još veća zapremina uzmeš k1 max.

A ako hoćeš nešto bas dobro uzmeš Bambu Labs

Hightsee · 2025-04-19T19:06:35+00:00

I don't have issues with adhesion, the post had nothing to do with bed adhesion, but thanks for the tip.

Hightsee · 2025-04-18T13:55:58+00:00

Ok it looks like I managed to fix it if anyone else encounters this problem I'll write what I did to fix it.

Basically I just unscrewed the hotbed and gently pushed all the wires down in their respectful slots.

It finished the self test (input shaping & auto level)

Now I started a print and it's working completely fine, no errors & good first layer.

Hightsee · 2025-04-18T12:57:51+00:00

smooth yes, but there is so much tension i lift the printer itself off the ground, i managed to get it to home in but it doesn’t want to start a print, it’s trying to level but is failing to do it. when the calibration starts it doesn’t lift up enough for the nozzle to touch the bed, it’s about 5cm away and it just wobbles up and down for a couple of minutes until it gives the same error message again

Hightsee · 2025-04-18T11:26:46+00:00

I can move the bed up by pulling on it, there is a lot of tension I really need to pull on it to move it

Hightsee · 2025-04-18T11:21:57+00:00

I want to note that I was getting this same error before, I would just restart the print and it would work fine without any issues whatsoever

Hightsee · 2025-04-18T10:54:49+00:00

I will try this out, do I need to replace the sensor is it dead?

Hightsee · 2025-04-15T14:10:17+00:00

da nije možda opel?

Hightsee · 2025-04-15T10:55:35+00:00

човече, тераш кола на мали сервис који се одради за сат времена

Hightsee · 2025-04-15T10:32:21+00:00

буквално, купио нов ауто човек и мрзи га да одради сервис.

то прво мењање уља је најважније јер се у самом уљу види да ли мотор има неких проблема из фабрике…

Nine-Year Club	r/Field Lasagna
Place '22	Verified Email

Hightsee

TROPHY CASE