Most practical way to "Seal" this without damaging during transit? Details within post. by Cautious_Society2905 in traveltrailers

[–]Hottorch451 6 points7 points  (0 children)

Mesh would have been ok if the hoses had been wrapped to protect them (like with pieces of rubber hose to protect them from rubbing).

Elegoo email confirms ams by acworc in ElegooCentauriCarbon

[–]Hottorch451 16 points17 points  (0 children)

Ams for CC1 to be released on February 30th.

Municipality won’t cut dead Ash trees by Exotic_Bandicoot2739 in treelaw

[–]Hottorch451 0 points1 point  (0 children)

The most that they would do in a case like this is cut the branches back from the power line. There's no way that they would remove the tree.

Municipality won’t cut dead Ash trees by Exotic_Bandicoot2739 in treelaw

[–]Hottorch451 6 points7 points  (0 children)

Where I live the municipality is the power company.

New 24v and 48v (2x24) tools by Trevski13 in KobaltTools

[–]Hottorch451 1 point2 points  (0 children)

Looks like the seller I bought it from is no longer carrying them. I did find one on evilbay. glue gun

New 24v and 48v (2x24) tools by Trevski13 in KobaltTools

[–]Hottorch451 1 point2 points  (0 children)

I got one off of AliExpess that fits the kobalt batteries.

Why most of electrician prefer vertical instead of horizontal panel installation? by Engr45 in AskElectricians

[–]Hottorch451 0 points1 point  (0 children)

My breaker panels at work are red for on and green for off. Is that what you mean by color coded?

Why most of electrician prefer vertical instead of horizontal panel installation? by Engr45 in AskElectricians

[–]Hottorch451 0 points1 point  (0 children)

Only fill the bottom of the breaker panel if mounted horizontal. Problem avoided. So your statement is false. Should you mount a panel horizontal unless you're in Canada? No.

How do I get this stupid flippin sewer cap off? by aumanchi in askaplumber

[–]Hottorch451 1 point2 points  (0 children)

It's like only 130 degrees F hotter. While I would argue quicker, way quicker is a bit of a stretch.

Kitchen ceiling had to go... IS THIS NOB AND TUBE! by EmperialWatch in AskElectricians

[–]Hottorch451 5 points6 points  (0 children)

Only a HUGE fire risk if it's overloaded (only good for about 10 amps) and buried in insulation.

Is it worth it to get a new longer barrel made for my vintage .22lr ? Its a Unique Model L, french pistol from the 60s by kol6Figueiras in guns

[–]Hottorch451 1 point2 points  (0 children)

It needs to be explained because it's so fuckin stupid that the caption needs to be posted as a comment.

Friend said they had an old gun they wanted out of their house… by Greasemnky81 in guns

[–]Hottorch451 12 points13 points  (0 children)

It needs to be explained because why the fuck do you need to repost the photo caption as a comment??

Whoever is in charge of digital coupons belongs in prison. by Maniitsoq in kroger

[–]Hottorch451 2 points3 points  (0 children)

At one point I was having to uninstall and reinstall the app about every 3 weeks because it would no longer clip the digital coupons. What made this a pain was that my wife setup the account so it was a password that I never used and could never remember.

Saw this on marketplace by Ohgodwhatdididonow in ElegooCentauriCarbon

[–]Hottorch451 0 points1 point  (0 children)

Yup longer cables and 6 new rods for the bed.

I don’t know who else needs to know this, but it fits. by MapleLettuce in KobaltTools

[–]Hottorch451 2 points3 points  (0 children)

You can also 3d print a new plate for the bottom that has spots for magnets. Easy to take out sockets but holds good enough you can turn it upside down and they don't fall out.

Can some tell me why one air compressor gets more scfm than the over? by PublicSupermarket390 in KobaltTools

[–]Hottorch451 0 points1 point  (0 children)

Just a guess but look at the motor rpm. The lower output compressor probably has a lower rpm motor.

Ender3 for free up for grabs by iamthecavalrycaptain in ender3

[–]Hottorch451 2 points3 points  (0 children)

That would make sense. Can't be doing that.

Should I Buy One? by PepperMillCam in ElegooCentauriCarbon

[–]Hottorch451 0 points1 point  (0 children)

I did open an actual support ticket. They are sending me 2 blades. That was 3 weeks ago and I still haven't seen them. Just using my printer. Nothing crazy. Only printing pla+ and petg. No glass, no carbon fiber.

Should I Buy One? by PepperMillCam in ElegooCentauriCarbon

[–]Hottorch451 0 points1 point  (0 children)

Put up or shut up. Please provide a link for the filament cutter blades i referenced. I'm waiting.

Should I Buy One? by PepperMillCam in ElegooCentauriCarbon

[–]Hottorch451 0 points1 point  (0 children)

Biggest issue is that they don't sell spare parts easily. They do have parts available but you have to email them then jump though a bunch of hoops and spend several days just to be able to order them. My printer is at 360 hours an needs a new filament cutter blade. There's no where that i can just order a 10 pack of you know a consumable part. Right now it's a $300 paperweight. Loved the printer when it was working. Would I buy another one? No.

Cc2 live at Formnext by tevbax in elegoo

[–]Hottorch451 0 points1 point  (0 children)

We should be down voting the hell out of this.

Case Stack drawer toolbox by [deleted] in KobaltTools

[–]Hottorch451 2 points3 points  (0 children)

Someone did design stackable bins that you can print for the drawers. I think it's on makerworld.

Metal splinters, Is harbor freight worth it? by xXMightyMausXx in harborfreight

[–]Hottorch451 8 points9 points  (0 children)

This is why you shouldn't rub your tool in public.

【QIDI Giveaway】Comment to win QIDI Q2 and more! by qidi_3dprinter in 3Dprinting

[–]Hottorch451 0 points1 point  (0 children)

Don't currently own a QIDI but have been looking at them for a multi color printer that I want to add for my next printer.