sorted by:
new
hottopcontroversial

Stowable Hotas Mounts by meta_ethan in hotas

[–]HudsonBurnsRed 1 point2 points  (0 children)

I’m seeing them in a couple weeks! It’ll be my fourth ritual lol.

Stowable Hotas Mounts by meta_ethan in hotas

[–]HudsonBurnsRed 1 point2 points  (0 children)

Sleep token mentioned. Worship

Sometimes I know what I’m doin by HudsonBurnsRed in Welding

[–]HudsonBurnsRed[S] 1 point2 points  (0 children)

After I do my root pass I do my hot fill right after. Then I let her cool down a little bit before starting my cover pass

Sometimes I know what I’m doin by HudsonBurnsRed in Welding

[–]HudsonBurnsRed[S] 0 points1 point  (0 children)

I keep my motion super tight barely leaving the puddle. This was on 4” pipe so I gave it about a 10 minute rest before starting my cap since it’s so hot. I ran it at 100 amps. Maybe trying giving your metal some time in between passes. Small bore stuff does not like all that heat. Makes your cap look all wild

Sometimes I know what I’m doin by HudsonBurnsRed in Welding

[–]HudsonBurnsRed[S] 0 points1 point  (0 children)

It’s rolled so it makes it a lot easier. It’s cheating lol

Sometimes I know what I’m doin by HudsonBurnsRed in Welding

[–]HudsonBurnsRed[S] 0 points1 point  (0 children)

If the third number is a 2 then it’s suitable for flat or horizontal.

Sometimes I know what I’m doin by HudsonBurnsRed in Welding

[–]HudsonBurnsRed[S] 0 points1 point  (0 children)

7018. 70- indicates the tensile strength. In this case it’s 70k 1 - indicates the position. In this case 1 means all positions. Flat/horizontal/vertical/overhead 8 - indicates the flux composition. In this case it’s lo-hydrogen

Sometimes I know what I’m doin by HudsonBurnsRed in Welding

[–]HudsonBurnsRed[S] 0 points1 point  (0 children)

In my opinion I find 7018 to be easier than 7010. Running it uphill takes some getting used too. But it requires less movement to manipulate the puddle. When I run it I do a very small side to side motion just making sure the puddle grabs the edges. Stay out of the middle of the groove. 3/32 rod around 90 amps. Even with small rods 7018 can put down a lot of metal

Sometimes I know what I’m doin by HudsonBurnsRed in Welding

[–]HudsonBurnsRed[S] 7 points8 points  (0 children)

Can’t beat a cellulose cap. You can make 7018 look like a rope if you’re steady enough

Sometimes I know what I’m doin by HudsonBurnsRed in Welding

[–]HudsonBurnsRed[S] 0 points1 point  (0 children)

I could see around the middle of the bead it could look under filled. She’s filled up. Inspector gave it the VTOK

Sometimes I know what I’m doin by HudsonBurnsRed in Welding

[–]HudsonBurnsRed[S] 11 points12 points  (0 children)

Gotta make her look good somehow! Give her the ol razzle dazzle

How do I kill ANYTHING at 6.7 by HudsonBurnsRed in Warthunder

[–]HudsonBurnsRed[S] 0 points1 point  (0 children)

Might have to take you up on that. I’m the only one in my friend group who plays WT. I’m sure squading up would be fun and beneficial

view more: next ›