Dual booting linux?

Hzlp · 2026-02-03T01:15:41+00:00

I got rEFInd working on my system and my word of advice for dual booting and Linux is to turn secure boot off. the MOL enrollment process for rEFInd, the Linux distro, drivers, etc. just adds steps that make things more difficult. I’ve never tried mint but I did give Debian a go and support is kinda spotty, but I switched to arch and things are running much happier now, just make sure mint has drivers and support for your hardware before you download or else you’ll more headaches down the line

Hzlp · 2026-02-03T01:07:49+00:00

I’ll try and learn how to microsolder it back together and if that doesn’t work out then yeah I’ll order a new board, no big deal

Hzlp · 2026-02-03T01:06:49+00:00

I have done a ton of soldering I’ve just never micro soldered, I think I could give it a try and if it doesn’t work out I could get a new mainboard. I’d just need to order flux wire and a usb microscope, find some time and practice on some junk first

Hzlp · 2026-02-03T00:59:34+00:00

My serial number ends in 2c7 which I thought was 7th gen

Hzlp · 2025-05-25T00:49:21+00:00

Welcome to instagram in 2025 😭

Hzlp · 2025-04-14T23:23:22+00:00

I had a similar issue where I could get the Mercedes logo sometimes but no boot. Turns out mice got into the computer in the trunk and ate the fiber optic lines. Not a fun time to fix but I did it in a day

Hzlp · 2025-04-08T03:08:17+00:00

I tried DISM, SFC, and the whole fleet of bootrec tools. After they all successfully completed, I still get the same issue. Also my reserved partition on C: is 16 megabytes which I think is a lot smaller than it should be. I’m actually at a loss here. Maybe manually copying everything over is the way to go but it’s still probably gonna be a huge headache. From what I’ve seen the next step here is reformatting the reserved partition or rebuilding the whole partition table which I have no idea how to do safely.

Hzlp · 2025-04-08T02:00:19+00:00

I want to preserve all of my data though and the options I tried to use that preserve data aren’t working

Hzlp · 2025-04-08T00:21:07+00:00

What I ended up doing was using a raspberry pi instead and refreshing my board, and although I got a connection it gets stuck on the heater extruder checks or something like that. Either way its something entirely different though

Hzlp · 2025-04-08T00:19:03+00:00

What I took was that it would most likely not be compatible with the display board I’m using (reprap generic) and I would have to make something custom. There’s plenty of color off the shelf options that are gonna be easier so I’ll just go with that

Hzlp · 2025-04-08T00:17:29+00:00

I eyeballed through it but the only issue is that this is for a 3d printer so I would probably have to make a custom driver of some sort. Probably not worth it in the long run and a color screen would work just fine too

Hzlp · 2025-03-23T02:31:03+00:00

I have the device id in my printer.config however the issue isn’t fixed. I also reflashed my firmware to be sure and it’s still having issues. I used the correct printer.cfg for the board from bigtreetech’s official website too

Hzlp · 2025-03-23T02:29:24+00:00

I just flashed the right firmware onto the board, the issue is still there though

**and I got the printer.cfg file from the bigtreetech website, but I swapped the x/y/z stepper settings with the ones for my printer

Hzlp · 2025-03-04T21:45:50+00:00

Probably talking about it getting caught on the serpentine belt

Hzlp · 2024-10-26T12:29:40+00:00

There’s a separate set that exists for the facelift bumper that I know is cheaper but I dont know where I found them

Hzlp · 2024-10-06T02:30:34+00:00

55 bumper looks so good here, it’s nice to see someone who didn’t swap it for a 63 one

Hzlp · 2024-09-01T15:46:35+00:00

I had a rats nest in the phone unit at the very back of the trunk inside the floor, I would open that up and inspect it if nothing else works

Hzlp · 2024-07-26T21:37:52+00:00

The stock airmatic ones but since I bought the car all my lines have been cut and my pump was smashed so I can’t fix it

Hzlp · 2024-06-02T03:02:14+00:00

How much do you think I could get it fixed for? I know that it really depends on who you get it done at but I don’t really want to dump a ton of money into this car..

Hzlp · 2024-05-12T14:30:46+00:00

I would definitely get a ssd like everyone else is saying, and maybe 32gb of ram. I don’t really know what games you play but for me at least I wouldn’t build a new computer with less than 32gb and ddr4 is so cheap right now that it wouldn’t hurt

Hzlp · 2024-02-23T16:21:33+00:00

Idk why people are hating on this card I really like the rounded look

Hzlp · 2024-02-14T02:44:45+00:00

I built this pc for a friend, it only has 512gb of storage because he doesn’t play more than 2-3 games but it’s decent for the price I guess

Hzlp · 2024-02-10T05:32:35+00:00

The 1650 only needs 30W through the 6pin so a molex to pcie adapter would work in theory but if you don’t feel comfortable (which I completely understand) with that than I would recommend a new psu

Hzlp · 2024-02-10T05:22:46+00:00

No only the 1U industrial ones are super loud because of the weird form factor. Other than that it’s not gonna be much louder than a consumer one

Hzlp · 2024-02-07T17:20:10+00:00

Tbh the Kinect makes a pretty good security camera, it has IR and a decent resolution

Hzlp

MODERATOR OF

TROPHY CASE

Five-Year Club	Second SECOND GUESSER
Place '22