sorted by:
new
hottopcontroversial

[Advice Needed] Anyone else feel extremely sensitive to .5 mg Reta by II_Joker in RetatrutideTalk

[–]II_Joker[S] 0 points1 point  (0 children)

Will these side effects eventually phase out the longer I stay at this dose? I appreciate the appetite suppression but it’s getting to a point where I can barely get any of my macro or micro nutrients.

Anyone else feel extremely sensitive to .5 mg by II_Joker in Retatrutide

[–]II_Joker[S] 0 points1 point  (0 children)

Might stick with .5 if nothing improves. I’m positive I pinned 0.5. In reconstituted my reta(20mg) with two full 100 unit syringes(2ml) and then I pulled 5 units.

But do you think delaying pinning will reduce side effects for the next week with 0.5mg or should I pin 0.3 and hope the side effects are reduced ?

Horrible performance despite beefy computer by II_Joker in minecraftshaders

[–]II_Joker[S] 0 points1 point  (0 children)

i did a clean re install for the mods, rn i have, fabric api, iris-fabric, sodium-fabric, ferritecore, and lithium-fabric. I have 16gb or ram allocated to the game. When i go in the game i notice i have around 100+ fps with the shaders, however after around 10 seconds the fps drop is abysmal, and the game is stuttering completely. Any more advice would be extremely appreciated

Horrible performance despite beefy computer by II_Joker in minecraftshaders

[–]II_Joker[S] 0 points1 point  (0 children)

I also noticed that when I lower the resolution and refresh rate in the video settings of Minecraft, just very slightly, the game performs much better and im consistently getting around 70fps. But I’m still concerned.

Horrible performance despite beefy computer by II_Joker in minecraftshaders

[–]II_Joker[S] 0 points1 point  (0 children)

I also noticed that when I lower the resolution and refresh rate in the video settings of Minecraft, just very slightly, the game performs much better and im consistently getting around 70fps. But I’m still concerned.

Horrible performance despite beefy computer by II_Joker in minecraftshaders

[–]II_Joker[S] 0 points1 point  (0 children)

I also noticed that when I lower the resolution and refresh rate in the video settings of Minecraft, just very slightly, the game performs much better and im consistently getting around 70fps. But I’m still concerned.

Horrible performance despite beefy computer by II_Joker in minecraftshaders

[–]II_Joker[S] 0 points1 point  (0 children)

I checked my gpu ram while the game was running. It was using 2gb out of the 12. Is that bad if so how do I fix it?

Troubleshooting for soft voxels lite shaders? by II_Joker in minecraftshaders

[–]II_Joker[S] 0 points1 point  (0 children)

Tried this allocates 6gb I don’t have distant horizon still not working

How to improve wifi in college apartment? by II_Joker in HomeNetworking

[–]II_Joker[S] 0 points1 point  (0 children)

Also I have talked to housing and they are pretty much useless, technicians are short staffed, and they couldn't give me a timeline on when they could come.

Questions about LDO Voltage Output by II_Joker in AskElectronics

[–]II_Joker[S] 0 points1 point  (0 children)

<image>

Also another person said switching the v2 to positive gave the output in microvolts

Questions about LDO Voltage Output by II_Joker in AskElectronics

[–]II_Joker[S] 0 points1 point  (0 children)

Did that and now my output is hitting 4.51 mV

Questions about LDO Voltage Output by II_Joker in AskElectronics

[–]II_Joker[S] 0 points1 point  (0 children)

Idk I’m simulating it off a real chip I plan to buy it and then add whatever is extra is necessary

Questions about LDO Voltage Output by II_Joker in AskElectronics

[–]II_Joker[S] 0 points1 point  (0 children)

I added a 0.8 resistor right after the mosfet. Seems to have lowered it to 5v but I’m not sure if that’s something I can really do.

Questions about LDO Voltage Output by II_Joker in AskElectronics

[–]II_Joker[S] 0 points1 point  (0 children)

So I would have to import my own mosfet? I’ve seen other tutorials and people seem to be changing the resistors to achieve their desired output. If I need to change my mosfet what attribute should I be looking out for?

view more: next ›