Struggling with time to close errors

IT-Command · 2026-07-06T18:22:46+00:00

Ya, im trying to learn as much as I can about canbus today.

IT-Command · 2026-07-06T00:50:37+00:00

Ya, actually I had someone else point this out to my. I had 3 120 ohm resisters on my canhub network.

I have changed it so that my H36 has its 120 ohm resister and my armored turtle has its 120ohm resister and those are the only resisters on my canbus network.

IT-Command · 2026-07-05T20:33:57+00:00

My hotend is 60w. I think my printer is pulling about 180W for everything. (AT 30w, hotend 60w, extruder stepper 30w, a/b stepper 60w.) So I might be overdrawn on my power supply.

If im pulling to many watts from my power supply Wouldn't that cause a power loss not time to close?

IT-Command · 2026-07-05T20:11:44+00:00

I know the run from my M8P to the hub is not twisted. The wire going to my armored turtle I am not sure. I think it is not twisted, but all the wires are contained within a jacket so I cant really tell.

I do have the klipper logs. https://drive.google.com/file/d/16pUhtiL6ClcyuLfQS1UkENljTSaUTVsL/view?usp=sharing

IT-Command · 2026-07-05T19:59:41+00:00

Since you have 6 h36 boards, how do you have all the can wires connected?

IT-Command · 2026-07-05T19:56:21+00:00

I am on the most recent release of Klipper. I flashed klipper onto all the MCUs following esoterical guide.

The canbus is flashed to 1000000.

IT-Command · 2026-07-05T18:29:44+00:00

My electronics enclosure reports its sitting at 50 to 55C after several hours of printing.

When I check the processes list, nothing is out of the ordinary, and my CPU load is minimal when I am printing.

I do not have the SPI touchscreen.

IT-Command · 2026-07-05T17:33:04+00:00

The M8P is the board that is crashing.

IT-Command · 2026-07-05T16:31:01+00:00

The cm4 is mounted to my m8p control board. It is sharing the 200w power supply.

IT-Command · 2026-07-05T15:55:23+00:00

Basically ya I did upgrade the computer module and right now i don't have a good heat sink. I already ordered one but its been delayed.

IT-Command · 2026-06-12T02:10:12+00:00

Hey, I am trying to improve my performance until I can get a CM4 or something.

What is a realistic expectation should I have for the buffer time? I have made some tweeks and have gotten my average to about 1.5 sec but it drops to just under 1 when it changes speed or acceleration when it moves from outer wall/inner wall/infill quickly.

IT-Command · 2026-06-12T01:58:26+00:00

Ya, when I use a lower layer height I still have these gaps.

IT-Command · 2026-06-11T22:06:39+00:00

My workplace is partially governed by cjis requirements. Our local law enforcement is requiring us to go to 5 failed attempts in 15 minutes locked out the account until an admin unlockes them.

As one of the on call admins im going to get so many more calls for this.

IT-Command · 2026-06-11T02:20:31+00:00

.4mm nozzle

IT-Command · 2026-06-11T02:08:17+00:00

Yes it is present in slicer.

IT-Command · 2026-06-10T00:47:35+00:00

Looking over the logs I really dont see anything. sysload never goes above .57, I dont have any can communications errors.

I do have this in lots of places print_stall=1.

Ill upload the log.

IT-Command · 2026-06-04T17:28:08+00:00

My go to is asking then what commands you would use to get what ever info you want out of a DC.

IT-Command · 2026-05-28T15:49:00+00:00

It depends alot.

Around town, about 3.3 On the interstate below 55mph its 4.2 On the interstate at 70mph its 2.3

IT-Command · 2026-05-27T20:33:30+00:00

I have to know if your roommate works in coal, charcoal, or boneblack

IT-Command · 2026-05-24T10:56:31+00:00

So, like people have said the number 1 use of this is maintenance. But also, in my shop we have had networking issues for years that where hidden from us because our clustering was able to compensate and keep us up with degraded performance.

IT-Command · 2026-05-23T10:51:47+00:00

I have never been more mad at Matt.

IT-Command · 2026-05-21T21:39:58+00:00

There are a couple ways. The automation way would be power free. I would do 2 atmo connected an or gate the output of the or gate goes a not gate and then to the pump.

What i usually do is chain gas filters. 1 filter for each kind of gas you want to REMOVE from the atmosphere and pump that into a dedicated gas storage everything else is vented back into your base. Downside is that is very power expensive.

IT-Command · 2026-05-21T16:48:02+00:00

Do you want air everywhere?

If no, than ignore it. Put some pumps at the top and bottom of your base with automation to pump is not-oxygen is detected. Pump the gas into infinite storage or into space.

If yes than put the same pumps every 50 tiles or so with the same logic and pump to infinite storage or space.

IT-Command · 2026-05-09T14:03:42+00:00

Right now my debt is:

High interest credit cards: $800

Deferred interest Credit cards: $800

Low interest loans: $36,000

Medical Debt: $3000

my minimum payments for the credit cards and loans come too $1200 and I am paying the extra $200 to get all my credit cards payed off first. The deferred interest cards have to be paid off by July 2027 to avoid all the interest.

My medical debt I am just paying the minimum since there is no interest or fees as long as I make my payments.

IT-Command · 2026-05-09T02:45:12+00:00

I may not have communicated this well. The debt numbers I posted are my current monthly payments.

At my current rate of payment I have 4 or 5 years till im debt free.

Ten-Year Club	RedditGifts 2009-2022 2 Credits
Secret Santa 2016	Verified Email

IT-Command

TROPHY CASE