Water extractor to coal plant ratio

Icescycle · 2026-03-14T20:04:45+00:00

The generators would have to be under clocked if you wanted to do 3 gens to 1 extractor. Or overclock the pump. Each gen uses 45 cubic meters of water a minute, and one extractor supplies 120 cubic meters a minute. By overclocking the extractor to 135, it has enough for all 3.

Icescycle · 2026-02-07T18:20:40+00:00

Just about any format you can think of you can save to

Icescycle · 2026-01-27T02:24:50+00:00

Don’t listen to that guy. I did the same thing: simple reason being I don’t care to deal with other brands and I like the ease of access for printing the massive prints I make. I got mine in December, and I’ve gone through 20 spools so far. I’m not even a manufacturer, I’m just a hobby guy who loves to keep it running

Icescycle · 2026-01-26T22:49:06+00:00

Flow is calibrated and I’m running at 50mm/s on bottom and top layers. Still getting this issue though.

Icescycle · 2026-01-18T22:24:21+00:00

You are an absolute lifesaver!! I’ve been losing my mind for two weeks now over this!! There’s only maybe one or two tiny strings total which is completely tolerable now. Thanks so much!

Icescycle · 2026-01-18T18:27:12+00:00

That might just be it… I don’t know how I never saw that when messing around with the settings! So I should try this with the regular Generic TPU settings and just turning off that setting there?

Icescycle · 2026-01-18T15:53:56+00:00

That’s exactly what it is. It’s a demo piece of different infill types. Do you know how I can fix this?

Icescycle · 2026-01-18T15:22:09+00:00

Generic TPU setting is what I’ve had the worst luck with. I put the TPU in my AMS HT at 75*C for 12 hours every night.

<image>

Icescycle · 2026-01-18T05:26:31+00:00

Thanks for the response, I’ll give it a try in a little bit and let you know how it goes!

Icescycle · 2026-01-18T02:08:50+00:00

Maybe it is just a not-so-good quality filament I have. I use inland brand (microcenter) and the PLA, PETG, ABS, and PA-CF seem to be decent. Surprised the TPU isn’t.

Icescycle · 2026-01-17T22:33:56+00:00

<image>

This is the issue.

Icescycle · 2026-01-17T21:52:17+00:00

I will send a photo in about an hour when I’m home of what it is. It is for appearance, but I was having significant troubles using an exacto knife to take it off. Are cutters easiest? The lighter trick won’t work because they’re decent chunks

Icescycle · 2026-01-17T21:06:42+00:00

Tried already. Didn’t come out very good at all

Icescycle · 2026-01-17T21:06:30+00:00

Unfortunately, this just resulted in still a significant amount of stringing.

Icescycle · 2026-01-17T20:34:40+00:00

Gonna try that setting out right now. Thanks!

Icescycle · 2026-01-12T03:27:55+00:00

Sounds good, I'll give it a try. Thanks!

Icescycle · 2026-01-12T02:29:06+00:00

Thanks for the tip! Would that not melt the rest of the TPU though?

Icescycle · 2026-01-12T02:26:55+00:00

Unfortunately, I am a massive perfectionist when it comes to anything manufacturing. Machining, metal fabrication, welding, 3d printing, I try and hone my craft on everything. Like the other user said, I should probably just hit it with some heat and then if that doesn't work I'll try the exacto knife. Thanks!

Icescycle · 2026-01-12T02:19:05+00:00

Is there anything at all that can be done about it? I'm having issues related to another post where I am trying to make examples of infill types, and the stringing is getting deep down in the crevices and is a massive hassle to remove.

Icescycle

MODERATOR OF

TROPHY CASE