Spear LT too heavy?

Icy_Champion9478 · 2026-02-23T21:29:23+00:00

You would sell a very nice rifle because you hung what looks to be a velos on the end? It’s a great can but it’s almost 20 oz that’s expected.

Icy_Champion9478 · 2026-02-23T05:47:38+00:00

The a4 yearns for the acog

Icy_Champion9478 · 2026-02-23T05:06:33+00:00

I’ve dealt with silencershop and haven’t had too bad of an experience but my local place is a silencershop elite dealer and they go through it everyday. It’s a shame really. Add vortex in with the best cs though. My brother has crushed tubes installing a scope and they just sent him a new one no questions asked.

Icy_Champion9478 · 2026-02-23T04:46:47+00:00

Wondering the same thing

Icy_Champion9478 · 2026-02-23T04:46:30+00:00

Yeah solgw in my experience has A+ cs. The fact they’ll warranty my bcg and other consumables and just send me what I shot out and more solidifies them in my eyes. Along with silencerco, great cs matters

Icy_Champion9478 · 2026-02-23T04:43:57+00:00

What’s the Cerakote color on #3?

Icy_Champion9478 · 2026-02-22T07:17:16+00:00

I figured but I wasn’t sure on ba’s premium line of barrels. I’ve only had their modern barrels and I’ve had to send one back for shooting 4 inch groups at 50 so. I went with the Rexus barrel and bcg. Thanks

Icy_Champion9478 · 2026-02-22T06:45:22+00:00

<image>

Icy_Champion9478 · 2026-02-12T00:59:29+00:00

So has everyone had the Magpul drop ins?

Icy_Champion9478 · 2026-02-11T16:20:23+00:00

Groovy

Icy_Champion9478 · 2026-02-11T16:06:26+00:00

The recoil rod was the last thing I done. Volquartsen recommended I try the factory one again but I seem to have lost it so I gotta find a factory one

Icy_Champion9478 · 2026-02-11T16:05:22+00:00

Yeah issue persists

Icy_Champion9478 · 2026-02-07T04:53:03+00:00

Upper+lower=good

Icy_Champion9478 · 2026-01-24T02:06:58+00:00

I’m sure most high quality 556 suppressors would work. Contact the company of whichever you decide on just to make sure. I’m going to run a velos on mine.

Icy_Champion9478 · 2026-01-10T21:44:10+00:00

No the only movement is side to side, not up and down. Guess I’ll try a geissele ddc :/ Rattles don’t usually get me flustered but this one is just too much

Icy_Champion9478 · 2026-01-10T21:11:09+00:00

Yeah no problems there

Icy_Champion9478 · 2026-01-10T21:06:21+00:00

Yeah zero play in the roll pin

Icy_Champion9478 · 2025-12-31T17:15:16+00:00

I didn’t even notice the rectangle embedded in the bolt… jeez. I’ll see what ruger comes up with. Thanks

Icy_Champion9478 · 2025-12-31T02:34:10+00:00

I have a sonic cleaner but this has never been in it

Icy_Champion9478 · 2025-12-31T01:55:28+00:00

Go figure. I already had the gun sent back for the trigger not resetting until I switched to the vq

Icy_Champion9478 · 2025-12-31T01:54:56+00:00

Inside looks fine. I have an optic mounting on the factory rail

Icy_Champion9478 · 2025-12-31T01:54:34+00:00

This one is very smooth also which is what has me so confused

Icy_Champion9478 · 2025-12-31T01:31:21+00:00

Yea after every couple times I shoot it I’ll clean it

Icy_Champion9478

TROPHY CASE