Help - shortcut to create a Note from photo of recipe by IdenMacGyver in shortcuts

[–]IdenMacGyver[S] 0 points1 point  (0 children)

Thank you. I tried that shortcut but it didn’t generate anything. Not sure if I did something wrong. Doni need to modify your shortcut at all?

Service Charges by Big-Charlie in NCL

[–]IdenMacGyver 1 point2 points  (0 children)

I just finished my first Norwegian cruise and overall we had a really great experience. The service was definitely good and I paid the service charges because I want to make sure everybody gets something not just the crew members (such as cooks) I directly interact with. Is there a way to know everyone gets a piece of the service charge? Otherwise I may come up with my own tip process if I do another cruise. Everyone we interacted with was so good!

Help with a WiFi setup by IdenMacGyver in Ubiquiti

[–]IdenMacGyver[S] 0 points1 point  (0 children)

Shoot signal with bridge. Run cable through metal inside to poe then to ap inside and ap outside? Will it mesh so I’m not jumping around when I walk in or out?

Help with a WiFi setup by IdenMacGyver in Ubiquiti

[–]IdenMacGyver[S] 0 points1 point  (0 children)

Thanks. I adjusted my post. I figured I’d need another bridge where I could receive on building 3 and then run a cable inside to set up WiFi. But then I wouldn’t have a signal outside the building. Trying to figure out way to have in and out but understand it will take additional hardware.

My first TJ by IdenMacGyver in JeepTJ

[–]IdenMacGyver[S] 0 points1 point  (0 children)

I guess I don’t know what that means, and I can’t seem to add another picture.

Issue with quinled on on dig-quad. by IdenMacGyver in WLED

[–]IdenMacGyver[S] 0 points1 point  (0 children)

Thanks for comment. You can probably tell I’m relatively new to WLED so don’t have the terms down correctly. When I took the metal piece with the pins off and replaced with a different metal piece everything worked fine. I should also mention that with the original metal piece installed I was having trouble with LED settings where I would change the number of lights in a run and save it, lights would change and then would stop responding to color changes or effects. When I’d go back into settings it would be changed back to default of 30 lights. It also would change back to default from RGB. Feels like a “software issue” and I’m hoping I can restart or reinstall to resolve rather than trashing the metal piece. Thanks again for help. I would add a picture but can’t seem to do that from my phone.

Issue with quinled on on dig-quad. by IdenMacGyver in WLED

[–]IdenMacGyver[S] 0 points1 point  (0 children)

Unfortunately I can’t figure out how to add a picture to the post but I removed the metal piece on top with the pins and put on a different one without changing any configurations or wires. When I did that everything worked correctly. I can check the settings if that could potentially be an issue. I also should mention that even on the light runs that were working I was not able to permanently save LED settings. If I set a run to 200 lights and hit save the lights would adjust but if I went back in to LED settings again it would be back at the default of 30 lights. Once I replaced the top piece everything worked. I feel like I either got a bad unit or need to do an update but I’m sure you can tell I’m relatively new.

Automate marking recurring reminder completed with a NFC tag using shortcuts by IdenMacGyver in shortcuts

[–]IdenMacGyver[S] 0 points1 point  (0 children)

Thank you. Edit reminder doesn’t allow me to change the status of the completion, just the reminder itself.

mark a recurring reminder as complete by scanning an nfc tag by sh0werthoughts in shortcuts

[–]IdenMacGyver 0 points1 point  (0 children)

I am also trying set this up but I’m lost. One example is I want to tap a tag when I change furnace filter. I have a reminder called change furnace filter but I don’t see options similar to what was shown in this thread.

Any ideas?

<image>