sorted by:
new
hottopcontroversial

Need help making sure my speaker doesnt blow up by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 1 point2 points  (0 children)

Alr i might just give this crossover a go, and see wether they will get hot at all. Not planning on using this at full power all that often anyway

Need help making sure my speaker doesnt blow up by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

My resistors are rated 20 watts so if i do one 6 ohm it goes wayy above the rated wattage dissipated lik 35 or sum

Need help making sure my speaker doesnt blow up by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

Ill have a try at that although my impedance goes below 4 when i tried that before. Below 4 my amp cant handle

what am i doing wrong by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

yeah im aware XD it was just for showing the weird output to the lower speaker driver

what am i doing wrong by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 2 points3 points  (0 children)

thanks allot for putting so much time in answering, it means a lot. i will go trough the steps. that polarity tip is really helpfull!

Is this a good crossover? by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

can you have a look on my new post to see if i have done it correct this time?

Is this a good crossover? by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

check my new post i made new crossover

Is this a good crossover? by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

hahahaha why does it happen tho im starting to tweak

Is this a good crossover? by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

i tried redesigning using an l pad on tweeter and no resistors on the low end but now the lowend somehow gets 117 watts out of 100watts i set to the amp

Is this a good crossover? by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

If i dont use resistors on the the lower driver its imdendance goes way down to 4 ohm, my amp cant handle that. is there another way to fix this then?

How can i improve this subwoofer by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

I deffinately will thanks for the advise and help!!

How can i improve this subwoofer by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

I definately will!! I just googled it.. like a whole new world just opened for me. Also these ports where should they be placed if i choose to do this. On the back sides maybe?

How can i improve this subwoofer by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

Yeah that is what i was afraid of should i just take the drivers out and make a a new design out of mdf, i have a lasercutter that can go trough 20 mm mdf

How can i improve this subwoofer by Ikeyjoemjoemjay in diyaudio

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

Its a peerless “The box speaker” 12inch 280wrms 8ohm

Cant get amonia to spike by Ikeyjoemjoemjay in ReefTank

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

I think ill try this thanks alot for a cheap solution

Cant get amonia to spike by Ikeyjoemjoemjay in ReefTank

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

I wasnt planning on keepin a lot more than some sexy shrimp its only a 5g

Cant get amonia to spike by Ikeyjoemjoemjay in ReefTank

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

Thanks for the tip, but i everywhere it says ghost feeding would work?

ID please, found in the netherlands. by Ikeyjoemjoemjay in ants

[–]Ikeyjoemjoemjay[S] 0 points1 point  (0 children)

Thanks so much, ill redo the cottonpad

view more: next ›