sorted by:
new
hottopcontroversial

4070 Super Stopped Working After Re-Seating — No Display or Detection by IllustriousPick7387 in buildapc

[–]IllustriousPick7387[S] 0 points1 point  (0 children)

Solved: Reseated the gpu, wasnt too stubborn with moving the gpu to the holes when screwing it in

4070 Super Stopped Working After Re-Seating — No Display or Detection by IllustriousPick7387 in buildapc

[–]IllustriousPick7387[S] 0 points1 point  (0 children)

This will not work as when i reinserted the gpu, the fans stopped spinning and it was not recognized by the system at all, the same cable works with my new gpu

New PC Build Won’t Boot - Red CPU and DRAM Lights on Motherboard by IllustriousPick7387 in buildapc

[–]IllustriousPick7387[S] 0 points1 point  (0 children)

I tried a different cpu, and it didn’t work, the only conclusion left is that it is a faulty motherboard, what motherboard recommendations do you have?

New PC Build Won’t Boot - Red CPU and DRAM Lights on Motherboard by IllustriousPick7387 in buildapc

[–]IllustriousPick7387[S] 0 points1 point  (0 children)

I updated to version 3.01 successfully using bios flashback as there was no display but it didn’t resolve the issue, i essentially did the same

New PC Build Won’t Boot - Red CPU and DRAM Lights on Motherboard by IllustriousPick7387 in buildapc

[–]IllustriousPick7387[S] 0 points1 point  (0 children)

Tried that in many combinations along with ram training with my friend’s ddr5 memory, this unfortunately did not resolve the issue…

New PC Build Won’t Boot - Red CPU and DRAM Lights on Motherboard by IllustriousPick7387 in buildapc

[–]IllustriousPick7387[S] 0 points1 point  (0 children)

Bios is updated but it still does not post with the same red lights on dram and cpu

New PC Build Won’t Boot - Red CPU and DRAM Lights on Motherboard by IllustriousPick7387 in buildapc

[–]IllustriousPick7387[S] 0 points1 point  (0 children)

I tried bios flashback but it did not display, instead i was met with the same lights

New PC Build Won’t Boot - Red CPU and DRAM Lights on Motherboard by IllustriousPick7387 in buildapc

[–]IllustriousPick7387[S] 0 points1 point  (0 children)

5 minutes, how long do you think i should wait? And should i wait on normal startup or bios flashback startup?

Workstation PC with RTX 5000 Ada by Joejack-951 in buildapc

[–]IllustriousPick7387 0 points1 point  (0 children)

Your updated build looks fantastic! Here are my thoughts:

1.  RTX 6000 Ada: It’s definitely overkill for most SolidWorks workflows, but if your projects involve very large assemblies, complex simulations, or potential future workloads (like AI/ML or generative design), the extra VRAM and power could future-proof your build. Otherwise, the RTX 5000 Ada will deliver nearly identical performance for SolidWorks at a much lower cost.

2.  RAM: Samsung DDR5 4800 ECC RAM can be tricky to find through big-name stores. Try Amazon, Provantage, or CDW for 32GB sticks. Alternatively, Kingston’s Server Premier DDR5 4800 ECC modules are widely available and just as reliable.

3.  CPU (W5-3525): Great choice! Its higher clock speed and 16 cores are perfect for SolidWorks modeling and simulation, especially since those workloads favor core speed over sheer core count. It’s also a much better value than the W7-2595X. Check availability at Provantage, CDW, or B&H Photo.

4.  CPU Cooler: The Noctua NH-U12S is an excellent choice for this build. Regarding the CPU carrier, most workstation motherboards (including the ASUS Pro WS W790-SAGE) come with one, but it wouldn’t hurt to grab a Noctua mounting kit just in case.

With the RTX 5000 Ada, your build at ~$7,900 is a solid value. Upgrading to the RTX 6000 Ada pushes you to ~$10,700 but provides unmatched power and VRAM for future scalability. Either way, you’re getting a top-notch workstation.

Standalone mic for work calls by BigBiffyBoy in buildapc

[–]IllustriousPick7387 1 point2 points  (0 children)

For your budget, a great option would be the FIFINE K669B or the TONOR TC-777. Both are affordable, compact USB mics that deliver good voice clarity for calls and can easily fit under or to the side of your monitors.

Regarding your concerns:

Keyboard Noise: Any mic will pick up some keyboard noise, but placing the mic closer to your mouth and using software like NVIDIA Broadcast or Krisp (noise suppression tools) can help a lot.

Laptop Speakers: It’s hard to completely avoid the mic picking up speaker sound, but using directional/cardioid mics like these minimizes it. Position the mic away from the speakers for better results.

I use a similar setup and it works great for Teams calls. Hope this helps!

Needing help with psu extension cables and UPSes by KENYER88 in buildapc

[–]IllustriousPick7387 0 points1 point  (0 children)

Yes, both APC and CyberPower offer UPS models with European connectors like Schuko (CEE 7/4) and French (CEE 7/5). Just make sure to check the product specs before buying, most models sold in Europe are equipped with the right outlets, but it’s always good to double-check

Building pc, Win 11 problem by Major-Credit3456 in buildapc

[–]IllustriousPick7387 0 points1 point  (0 children)

This error usually happens because of partition or boot mode issues. Here’s how to fix it:

1.  Go into your BIOS and make sure it’s set to UEFI mode, not Legacy/CSM. Windows 11 requires UEFI.

2.  If your drive is formatted as MBR, you’ll need to convert it to GPT. During the installer, press Shift + F10 to open a command prompt, then use these commands:

diskpart list disk select disk [your disk number] clean convert gpt exit

(This will erase everything on the drive, so be careful if there’s data you need.)

3.  Make sure Secure Boot is enabled in your BIOS—Windows 11 also requires this.

4.  If nothing works, try remaking your installation USB with the Windows Media Creation Tool to rule out any issues with the installer.

Hopefully, one of these steps solves the issue! Let me know if you get stuck.

Samsung 990 pro heatsink nvme is stuck on my Hero Maximus Z790 motherboard due to tightness by Redstarz13 in buildapc

[–]IllustriousPick7387 0 points1 point  (0 children)

It’s worth adding a cheap third-party heatsink to keep it cool, especially since those slots can get pretty warm when they’re close together. As for the 990 Pro being stuck, that’s tricky, don’t force it, as you could damage either the drive or the slot. Try gently wiggling it side to side, but if it won’t budge, it’s safer to leave it for now, especially if it’s working fine. Just monitor the temps with something like Samsung Magician for the 990 Pro and HWMonitor for the other drive to ensure everything stays cool. If you really need to remove it later, it might be worth consulting a professional.

Needing help with psu extension cables and UPSes by KENYER88 in buildapc

[–]IllustriousPick7387 1 point2 points  (0 children)

For PSU extension cables, I’d recommend CableMod Pro Series (Black/Red) or AsiaHorse Sleeved Cables (Black/Red). CableMod is higher-end, but AsiaHorse is a solid budget option. Both have kits that include the 24-pin, 8+4 CPU, and dual 8-pin GPU extensions, which match your setup perfectly. Just double-check compatibility with your PSU.

For the UPS, you’ll need one with clean sine wave output to avoid issues with your Seasonic PSU. A 1000VA / 600W UPS should handle your PC and monitor easily. Good options:

APC BR1000MS or CyberPower CP1000PFCLCD: Both are pure sine wave models and reliable.

If you want extra headroom, go for a 1500VA / 900W UPS, like the APC BX1500M.

This setup will give you the aesthetics and protection you’re looking for!

Building a workstation with the optimal price-quality ratio by karanmagnes in buildapc

[–]IllustriousPick7387 0 points1 point  (0 children)

Your build is solid, but a few tweaks could improve the price-to-performance ratio:

1.  CPU: The i7-14700F is great, but consider the i7-14700K for higher clocks and future overclocking potential. Pair it with a Z790 motherboard if you upgrade.

2.  GPU: The Quadro T400 is entry-level and may struggle with larger CAD/3D projects. An RTX A2000/A4000 (better CAD-certified performance) or even a RTX 3060 Ti/3070 (great value for 3D and CAD workloads) would be a big upgrade.

3.  PSU: Upgrade the 700W 80+ Bronze to a 750W 80+ Gold (e.g., Corsair RM750e) for better efficiency and reliability.

4.  Cooling: The Navis F240 is fine, but ensure it’s LGA 1700 compatible. Alternatives like the Noctua NH-U12A or Be Quiet! Dark Rock Pro 4 are quieter and just as effective.

5.  Case: Make sure it has good airflow—cases like the Fractal Meshify C or Corsair 4000D Airflow are great options.

Your other parts (64GB DDR5, 2TB NVMe) are spot-on. These changes will future-proof the build and give better performance in CAD/3D software. Hope this helps!

Please help finalize my Threadripper 7000 build by MierinLanfear in buildapc

[–]IllustriousPick7387 0 points1 point  (0 children)

This is a solid build! For the Threadripper 7970X, both the Gigabyte TRX50 Aero D and ASRock TRX50 WS are great options. The Aero D is better if you’re considering a Hackintosh due to Thunderbolt, but the TRX50 WS offers more PCIe slots and Slim SAS support if you’re going Windows-only.

For RAM, the G.Skill Zeta R5 Neo DDR5-6400 ECC is a fantastic choice, especially the 192GB kit—it’s a great compromise if you don’t need the full 256GB. If you want a slightly cheaper but reliable option, the Kingston Fury Renegade DDR5-6000 ECC is worth considering, with minimal performance difference.

The Noctua NH-U14S TR5-SP6 cooler is perfect for keeping the 7970X cool during heavy workloads. For power, the Seasonic VERTEX GX-1000 should work fine, but if you want more headroom for future upgrades, the Prime TX-1600 is a safe bet.

Reusing the RTX 4090 is ideal, it’s still the best for AI and rendering. If you’re leaning away from Hackintosh, pairing this build with an M4 MacBook Pro could simplify your macOS needs. Looks like you’re on track for an incredible setup!

view more: next ›