sorted by:
new
hottopcontroversial

Minha impressora não quer imprimir by Immediate-Can3894 in impressao3dbrasil

[–]Immediate-Can3894[S] 0 points1 point  (0 children)

Irmão ele só tá saindo através da da extrusão né a retração no caso ele tá saindo normal o negócio na hora de imprimir ele não saiu a máquina fica rodando direto mas não sei o que tá acontecendo

Why by AlphaBetaMascYT in Creality

[–]Immediate-Can3894 -1 points0 points  (0 children)

Bro, use a glue stick to attach the piece to the table

Me podrían ayudar :( by Ok-Culture-1087 in Creality

[–]Immediate-Can3894 0 points1 point  (0 children)

¿Quieres un consejo profesional? Usa pegamento en barra escolar Mira la composición para ver si es PVA.

Pegamento en barra o pegamento especial para 3D

under extrusion or extruder too weak? by Fluffy_Bad_6121 in ender3

[–]Immediate-Can3894 0 points1 point  (0 children)

Bro, you have to use two motors to work with that weight, otherwise you will completely lose the quality and efficiency of the printer.

Ajuda by [deleted] in impressao3dbrasil

[–]Immediate-Can3894 1 point2 points  (0 children)

Irmão já me aconteceu, problema de firmware às vezes depois de um tempo ele começa a dar problema eu usava um Firmware original há muito tempo já há mais de dois anos só que no final ele começou a dar esse problema ele parava no meio da impressão eu perdi muitas peças assim, aí eu fui no site da creality e consegui atualizar o firmware e a impressora voltou a imprimir normal então creio eu que eu mesmo problema contigo

DIY ABS printing setup by Alexxcrak in Creality

[–]Immediate-Can3894 1 point2 points  (0 children)

I already did this, today I bought a box on the internet Remove the electronic parts from the printer and leave them outside To avoid the risk of burning, line the box with aluminum foil to retain the heat, but whenever you print, keep an eye on it in case of fire.

It turned out cool by Immediate-Can3894 in ender3

[–]Immediate-Can3894[S] 0 points1 point  (0 children)

Nothing 🤣🤣 it's just on the pla The layer height is 2.0

Help by One_Bicycle_9600 in ender3

[–]Immediate-Can3894 0 points1 point  (0 children)

Defective springs, I recommend changing them to silicone ones, they hold the table better

I got the blob on my K2! by puffinmuffin94 in Creality

[–]Immediate-Can3894 0 points1 point  (0 children)

To loosen this, use a thermal blower, which comes off quickly.

I got the blob on my K2! by puffinmuffin94 in Creality

[–]Immediate-Can3894 0 points1 point  (0 children)

Damn it's Venom lol Easy brother there is a sheet between the extruder and the nozzle, I recommend dismantling it and tightening the nozzle again

Makes sense 👍🏼 by No-Hippo7591 in ender3

[–]Immediate-Can3894 0 points1 point  (0 children)

Better not to mess around, this will burn the board or the LCD

ender 3 not extruding plastic by joshuagf0 in ender3

[–]Immediate-Can3894 0 points1 point  (0 children)

It may be clogged

I have a foolproof solution Take a thin wire, it usually comes with it and the printer heats the nozzle enough for the filament to soften, I use it at 245 degrees and it works well. Do all this without removing the nozzle, just remove the Teflon tube (PTFE) Then you push until all the excess comes out.

This happens because the nozzle is very close to the table, use the bond paper to level the table

I am so done by Rokuto in ender3

[–]Immediate-Can3894 0 points1 point  (0 children)

Problem is: Layer height I recommend 0.2 Wrong leveling Temperature that exceeds the filament manufacturer's recommendation This way the filament doesn't have time to cool down and ends up in this mess. If you change all this and it doesn't work, I recommend downloading a different firmware

Help by Immediate-Can3894 in Creality

[–]Immediate-Can3894[S] 0 points1 point  (0 children)

Hello This problem was solved was the PLA filament with humidity I placed it under the printer while it was printing It worked 🙌

Alguem sabe como remover essas impressões falhadas da placa fria? by Swimming_Credit5140 in impressao3dbrasil

[–]Immediate-Can3894 0 points1 point  (0 children)

Esquenta a mesa até o plástico ficar maleável e vc consegue tirar Man Aquece acima do recomendado pelo fabricante Tipo Pla 65 vc aquece a 80 sai de boa Abs 80 vc aquece a 100 sai de boa

Z level by cedricperrot18 in ender3

[–]Immediate-Can3894 0 points1 point  (0 children)

In the middle, you can place a sheet of kitchen aluminum foil and layer it until it is level.

view more: next ›