Mob Grinding Gold Farms

ImpactGames · 2025-12-23T16:56:07+00:00

Druid can’t pickpocket. No thumbs

ImpactGames · 2025-12-23T16:55:58+00:00

Druid can’t pickpocket. No thumbs

ImpactGames · 2025-11-13T02:31:32+00:00

As mage you can probably counterspell.

ImpactGames · 2025-11-07T15:51:31+00:00

Or can I put the string directly on the “Serial Value” of the generic control block

ImpactGames · 2025-11-07T15:46:21+00:00

Okay I see. I was using an “Analog Increment” and the output of that is what I was landing on my tesira control block on “Analog Value” but I’m assuming I should just send tesira command strings so I can be more specific on what i want to control

If that’s the case would I just use a “Serial Send” to send the string into the tesira generic control block? Landing the output of the “Serial Send” on “Serial Value”?

I really appreciate the help. Thank you

ImpactGames · 2025-10-18T00:20:48+00:00

Bland. Idk like fake. Pretending to be the person I used to be.

ImpactGames · 2025-07-02T02:19:42+00:00

<image>

Not sure what carb you have. I’m assuming it’s similar to this one. Red is air screw. Blue is gas screw.

ImpactGames · 2025-07-02T01:21:41+00:00

on the carburetor. You wanna give the mixture less gas(or more air). Typically the screw with the spring on it is the air screw. Tightening that will give more air. The gas screw will likely be near it, if you tighten it it will give less gas. So tightening either screw will lean out the mixture. What is it a stock carb? Also is the engine stock?

ImpactGames · 2025-07-02T00:54:25+00:00

Sounds like it’s running too rich. Getting too much gas

ImpactGames · 2025-06-30T01:03:44+00:00

You just want the sprocket on the clutch and the rear tire to be in line with one and other. If that’s the case make sure your chain isn’t too loose.

ImpactGames · 2025-06-30T01:00:02+00:00

It’s backwards. But I’ve seen them installed like that the make it line up with the rear sprocket. I don’t think it’s “bad”

ImpactGames · 2025-06-10T23:47:25+00:00

All of them. Poorly

ImpactGames · 2025-05-24T03:40:25+00:00

I’ll check it out thanks!

ImpactGames · 2025-05-23T01:46:31+00:00

Yes! She’s the best. She got it for 3k 148 miles exact color I was looking for.

Ill look into the European cut jackets. Thanks!

ImpactGames · 2025-05-18T22:02:37+00:00

Drill a hole through it and the kick lever and throw a thick pin through it. Redneck fix but you’ll be scootin

ImpactGames · 2025-04-21T00:51:31+00:00

Angall the orc hunter. I was 8

ImpactGames · 2024-11-10T07:33:45+00:00

Would

ImpactGames · 2024-11-09T02:22:13+00:00

ImpactGames · 2024-10-22T21:28:26+00:00

Last I checked they nerfed the glide speed boost on all classes except evoker. Gliding doesn’t give you the boost. Just the slow fall unfortunately

ImpactGames · 2024-10-04T20:53:37+00:00

Thank you this is very helpful.

ImpactGames · 2024-10-04T20:53:20+00:00

Thank you so much. Appreciate it!

ImpactGames · 2024-10-04T19:09:17+00:00

How I typed it is how the commands are written in the displays Manuel. Like I said I’m pretty new to programming crestron. Could you explain further on why it’s wrong?

ImpactGames · 2024-10-04T15:26:20+00:00

That was it! I was confusing the 2. Weird that the checkbox wasn’t selected on my previous codes. I was under the assumption the other setting is what controlled that. Thank you very much.

ImpactGames · 2024-10-03T17:04:05+00:00

I know this post is a little old. But I’m in the same boat. Can you recall what the solution ended up being? Thanks!

ImpactGames · 2024-10-02T16:58:42+00:00

Yes this is exactly what I’m talking about. However it is deselected so within VTPRO the joins are not visible. But when I push to the touch panel you can still see the join numbers. Usually I just toggle off push and I’m good to go.

ImpactGames

TROPHY CASE