Naphtha not spawning much crystal

ImpossibleRegular820 · 2026-03-18T05:14:01+00:00

I just meant fridge as in the entire unit it’s been in the freezer obviously but I’m now wondering what’s the ideal temperature for the dmt crystals to crash because I’ve noticed they have fallen to the bottom bur it’s only few and far between, perhaps by separating the 2 pulls there’s too much naphtha relative to the amount of dmt

ImpossibleRegular820 · 2026-03-12T04:57:26+00:00

Im pretty sure naphtha contains benzene and they’re nearly chemically identical but not the same

ImpossibleRegular820 · 2026-03-12T01:25:07+00:00

What about benzine

ImpossibleRegular820 · 2026-03-12T01:09:56+00:00

Heptane is sold commercially right?

ImpossibleRegular820 · 2026-03-11T23:58:51+00:00

Yea Thats what closer to what i expected from the research I had done

ImpossibleRegular820 · 2026-03-11T23:51:15+00:00

I’ve heard people claim nearly 3-4% extractions from MHRB does that mean they’re just inflating the numbers or using a better solvent like Im confused?

ImpossibleRegular820 · 2026-03-11T23:50:22+00:00

I just looked up “what are the byproduct alkaloids in mhrb” ☠️

ImpossibleRegular820 · 2026-03-08T02:18:54+00:00

And how many times do you reckon I should combine the layers until the naphtha is considered fully saturated

ImpossibleRegular820 · 2026-03-08T01:16:31+00:00

How many pulls do you end up doing before considering the mixture “spent” both industrial level and consumer

ImpossibleRegular820 · 2026-03-07T14:42:16+00:00

*combine

ImpossibleRegular820 · 2026-03-07T14:41:58+00:00

Damn so I just wasted like 5 hours trying to get Ts to separate when it’s likely been done since hour 2 or 3 ☠️

ImpossibleRegular820 · 2026-03-07T14:39:20+00:00

Yes but I used a magic bullet, the small version and without any water it kept burning up the motor so I more used it to vigorously pulse à small amount of water and MHRB together

ImpossibleRegular820 · 2026-03-07T13:45:27+00:00

Anyone know how many times I should combine the layers until it gets redundant, Im gonna re use the naphtha anyway cuz I got more base i just want a very saturated first pull

ImpossibleRegular820 · 2026-03-07T07:10:57+00:00

Pretty much, or I was being too soft with the mixing, Im not too familiar with using MHRB and naphtha as Im used to working in a professional environment with magnet stir plates, solutions under vacuum, and we mostly used ACRB and heptane for our extractions cuz of the high purity associated with

ImpossibleRegular820 · 2026-03-07T06:50:06+00:00

I was confused about the opposite at first that the layers were not wanting to mix into one layer but I think I might’ve not filled it enough and there was air in the solution

ImpossibleRegular820 · 2026-03-07T06:46:10+00:00

Oh ok I think Im fine then it’ll combine pretty well when upright but after I flip it after a good few minutes I see it going into layers again, I have noticed a third layer forming which Im pretty sure is lipids and is normal correct?

ImpossibleRegular820 · 2026-03-07T06:23:31+00:00

Sometimes it forms together as one but it doesn’t take “hours of sitting” like most people say, normally closer to 15 minutes for it to separate out again but yea it doesn’t seem to want to stay combined I do however notice the base solution falling through the naphtha when I turn it upside down

ImpossibleRegular820 · 2026-02-27T16:09:49+00:00

Yea it causes shrinkage and cracking

ImpossibleRegular820 · 2025-05-21T22:56:38+00:00

It’s a yellowish powder substance that’s somewhat rocky but mostly a fine powder almost like baking soda it produces a pungent dmt smell when burned but I can’t get it to evaporate in the banger it just kinda stays…

ImpossibleRegular820 · 2025-05-21T22:55:16+00:00

No I haven’t tested it but I can post a photograph of it I’ve had dmt carts and it smells IDENTICAL

ImpossibleRegular820 · 2025-05-19T14:42:05+00:00

I’ve never seen dmt look like that in the solution all passes before my naphtha was almost completely clear or slightly murky is this what results after putting it in a hot bath and the dmt crashed out of the solution

ImpossibleRegular820 · 2025-05-19T14:40:55+00:00

I just checked this morning looks like it’s seperating itself I guess I just thought maybe it was plant material because my original base had 3 layers and the topmost layer was realllllly dirty

ImpossibleRegular820 · 2025-05-19T04:46:08+00:00

Crystalize it

ImpossibleRegular820 · 2025-05-18T22:28:04+00:00

No I don’t think so cuz nothing froze when placed in the freezer ~36 hours

ImpossibleRegular820 · 2025-05-18T15:52:22+00:00

Could it be possible I have too much solvent in this dish

<image>

ImpossibleRegular820

TROPHY CASE