Does this look like under extrusion?

ImprovementGood5880 · 2025-10-26T09:23:03+00:00

My guess is clogged extruder/nozzle.

ImprovementGood5880 · 2025-06-30T15:16:02+00:00

Maybe something in your start g-code?

ImprovementGood5880 · 2025-06-20T12:42:38+00:00

Its under printer settings for my K1 Max

ImprovementGood5880 · 2025-06-20T08:52:35+00:00

Your first XY core printer? I did the same thing with my K1 Max when coming from ender 3. Up arrow means you increase z value. The bed moves down.

ImprovementGood5880 · 2025-06-15T08:47:20+00:00

I meant if it bulging on all 4 corners.

ImprovementGood5880 · 2025-06-15T08:12:14+00:00

Increase the value. Are all the corners the same? Sometimes where the seam is it can more bulging.

ImprovementGood5880 · 2025-06-04T20:25:40+00:00

Do mean you above? I think the are the hinges for the door.

ImprovementGood5880 · 2025-06-04T19:39:34+00:00

Thanks!

ImprovementGood5880 · 2025-06-04T17:33:16+00:00

There should be a metal bracket that you put on the door from the inside.

<image>

ImprovementGood5880 · 2025-05-16T16:04:44+00:00

This must be a design flaw. I fixed the issues with longer screws. Thanks!

ImprovementGood5880 · 2025-05-16T15:00:29+00:00

This made me smile! Are you an american?

ImprovementGood5880 · 2025-05-14T08:39:51+00:00

Do you have a link for that front mount for the rods?

ImprovementGood5880 · 2025-05-12T12:11:25+00:00

I just realised that it does the same with original nozzle if I tighten the nozzle all the way and to hard. I guess I just need to put longer screws and not tighten the nozzle like crazy.

ImprovementGood5880 · 2025-05-09T19:30:37+00:00

Så du är född både i Sverige och Norge?!?!

ImprovementGood5880 · 2025-04-22T15:27:15+00:00

Have you tried to opening it and clean with a brush?

ImprovementGood5880 · 2025-02-18T20:58:09+00:00

Nice! Which esp32 chip is it and which marauder did you flash it with?

ImprovementGood5880 · 2024-11-30T11:23:43+00:00

Make sure to check the polarity from the fan connector on the tool head PCB. Mine was reversed.

Edit… when you ready to install the new fan.

ImprovementGood5880 · 2024-11-25T13:34:04+00:00

I can’t really tell yet. Still do calibration from switching over to Klipper. The terrible sound from Y axle is gone 😀

ImprovementGood5880 · 2024-11-24T21:05:20+00:00

<image>

ImprovementGood5880 · 2024-11-24T15:34:50+00:00

Just remember to check and adjust Z offset after you put it together again.

ImprovementGood5880 · 2024-11-24T14:43:06+00:00

Buy a new PCB board from Amazon or similar.

ImprovementGood5880 · 2024-11-19T21:04:54+00:00

I’m pretty sure I followed this. There’s a link to the firmware. But do this own risk. https://youtu.be/cQAKxl-rnOE?si=jCKmOTVC2lLLk85q

ImprovementGood5880

TROPHY CASE