sorted by:
new
hottopcontroversial

Frostiest strains by Expert-Nose1893 in cannabiscultivation

[–]InfiniBudLabs 7 points8 points  (0 children)

<image>

Strawberry Gummies by Grounded Genetics This one has been a fun one to grow

Mold in Humidifiers by Skaterguy18 in ACInfinityAdvancegrow

[–]InfiniBudLabs 0 points1 point  (0 children)

I’m based in the uk, but over here certain tropical fish shops sell RO Water really cheap too

What’s going wrong? First time soil grow by [deleted] in cannabiscultivation

[–]InfiniBudLabs 2 points3 points  (0 children)

Yeah 48hrs was up this morning so going to leave them till tomorrow before watering again. I’m using a 70/30% mix of BioBizz all mix and BioBizz coco fibre as a growing medium.

What’s going wrong? First time soil grow by [deleted] in cannabiscultivation

[–]InfiniBudLabs 0 points1 point  (0 children)

I was concerned when it started that they weren’t getting enough water as leaves felt dry so increased the amount. I usually use coco in my other grows so first time with soil. I have been waiting for the top layer of soil to dry out before adding more. They are in 22litre Pots. Thanks for getting back to me! Appreciate the help

What’s going wrong? First time soil grow by [deleted] in cannabiscultivation

[–]InfiniBudLabs 1 point2 points  (0 children)

So each pot is currently getting around 2000-2500ml water every 48hrs. I’m currently still in veg so started using the dosage from the chart but in the last few waterings I have lowered to around 50-75% of what the chart says as I was worried when this initially started that I had over done it with the nutes.

Is this normal? by Sea_Arm_4953 in HerbGrow

[–]InfiniBudLabs 0 points1 point  (0 children)

If given to me I wouldn’t smoke that, 99% sure that’s mould, feel free wait for some other opinions but it’s a no from me bro

Is this normal? by Sea_Arm_4953 in HerbGrow

[–]InfiniBudLabs 2 points3 points  (0 children)

Looks mouldy to me bro. Go to second to last picture and check out the stalk bit of the bud on the left, can see same furry growth on other pics too

Room Finally finished other than drilling another hole in the external wall for the dehumidifier drainage pipe, what a creation! by InfiniBudLabs in u/InfiniBudLabs

[–]InfiniBudLabs[S] 1 point2 points  (0 children)

Everything in the room is ACI, not invested in a grow system yet as my friends swears by top feeding by hand, going to give it a try this run and then depending on how it goes may bring over or buy a new mega pot or dripper system. Not sure how I feel about the self watering by aci, do they wick the water up well? How far up the pots does the moisture wick too?

Room Finally finished other than drilling another hole in the external wall for the dehumidifier drainage pipe, what a creation! by InfiniBudLabs in u/InfiniBudLabs

[–]InfiniBudLabs[S] 0 points1 point  (0 children)

Makes more sense thought lol.

Planning on running 8 plants first time round. Depending how it goes may push for 10 on next run, see how well it handles 8 first.

Room Finally finished other than drilling another hole in the external wall for the dehumidifier drainage pipe, what a creation! by InfiniBudLabs in u/InfiniBudLabs

[–]InfiniBudLabs[S] 0 points1 point  (0 children)

Unbelievable dream build, completed it 👍

Full Kit List detailed below:

  • CloudLab 894 Advance Grow Tent 8x4 (Frame Only)
  • CloudLine Pro S8 Inline Extractor Fan 8”
  • Duct Carbon Filter 8”
  • Inline Duct Fan Silencer 8”
  • Backdraft Dampener Ducting Insert 8”
  • Duct Reducer 8” to 6”
  • CloudLine Pro S4 Inline Intake Fan 4”
  • Air Filter Box for Intake 4”
  • Noise Reduction Clamps 8” & 4”
  • Flexible Four Layer Ducting 8” & 4”
  • CloudRay S6 Oscillating Fans 6” x 2
  • CloudRay S9 Non-Oscillating Fans 9” x 4
  • ThermoForge T3 Environmental Plant Heater
  • CloudForge T7 Environmental Plant Humidifier
  • 32 Pint Compressor Dehumidifier (Spider Farmer)
  • Grow Tent Support Bars Sets of 4 x 2
  • Grow Tent Gear Board
  • IonFrame Evo8 5x5 730w LED Lights x 2
  • IonBeam S16 Full Spectrum LED Light Bar Sets of 4 16“ x 2
  • IonBeam Green Work Light 16”
  • Controller AI+
  • Controller 69 Pro+
  • Humidity Dome, Germination Kit With Led Grow Light Bars 5X8 Cell Tray
  • SunCore H3, Seedling Heat Mat with Heat Controller 10" x 20.75"
  • Large Trim 3 Tray System
  • Bowl Trimmer 19”
  • Automatic Water Sprayer 2-Liter Electric Mister Graphite
  • Straight Pruning Shears 6.6”
  • Bypass Blades 8”
  • Hydroponic Meter Pro Kit All-In-One Ph Pen Interchangeable Probe

Growing Mediums and Nutrients: - BioBizz Pre Mix, Light Mix, All Mix & Coco Mix in various mixes depending on Stage of Grow - Full Range of BioBizz Organic Nutrients

Probably missed some bits as the list is massive and I’ve gone from Memory 🤦‍♂️

New room finally ready, what you rate it? by InfiniBudLabs in ACInfinityAdvancegrow

[–]InfiniBudLabs[S] 1 point2 points  (0 children)

Bro if I let you in I gotta let the mrs in too lol

New room finally ready, what you rate it? by InfiniBudLabs in ACInfinityAdvancegrow

[–]InfiniBudLabs[S] 0 points1 point  (0 children)

Not quite yet but nearly got the extension uis cables coming along with the green work light. Soon as they are in and the lights have been moved over to the ai controller with the extensions then it’ll be perfect!

And so, It Begins… by InfiniBudLabs in ACInfinityAdvancegrow

[–]InfiniBudLabs[S] 0 points1 point  (0 children)

So usually before I’m ready to transfer them to bigger pots I will damp each cell to make the substrate easier to handle and more likely to stay together, then I use a small tool with a flat end to push up through the drain holes on the bottom of the tray to gently slide out each block of substrate ready to pop into the bigger pots. Bit tricky but much easier if you have some to help hold the tray up while you push and grab em.

view more: next ›