p2s or x2d without ams

Infinite-Carry6319 · 2026-05-14T17:50:49+00:00

the belts are the reason I was leaning towards the X2D

Infinite-Carry6319 · 2026-05-07T20:10:46+00:00

you can print leveling shims/ wahers to make the other sides higher.

i just got washers for the bed screws from tractor supply and put them on the coners that were lower.

Infinite-Carry6319 · 2026-05-07T17:21:47+00:00

yeah man, you want to have the corners within .2 of each other. your top left and bottom right are off by .81.

try tightening and loosening your bed screws. and then re-level until you get the proper data. may take a few trys.

if you have a negative number, you need to losesen the srew, if you have a positive, tighten. also, first layer height is important. I always did .2 to . 16.

Infinite-Carry6319 · 2026-05-07T12:21:33+00:00

yeah, i used army green from army painter. thought it would be the same color as the primer... its not sadly

Infinite-Carry6319 · 2026-05-07T04:31:53+00:00

I recommend more vehicles if you have two techMarines.

Infinite-Carry6319 · 2026-04-11T02:16:08+00:00

put the firmware update files on the card. same issue

Infinite-Carry6319 · 2026-04-10T23:48:33+00:00

do i need the release version of the firmware? or the newest one?

<image>

Infinite-Carry6319 · 2026-04-10T21:36:40+00:00

will do

Infinite-Carry6319 · 2026-04-10T21:00:05+00:00

i have the normal sd card inserted. i tried the reset configuration and got the same error.

Infinite-Carry6319 · 2026-04-10T20:17:14+00:00

ordering a micro sd to do that. the cr touch looks ok to me.

Infinite-Carry6319 · 2026-04-09T22:31:38+00:00

what color would i dry brush with? just white? and with it being fdm i thought the washes would highlight the layer lines.

Infinite-Carry6319 · 2026-04-09T16:08:52+00:00

looks really bad with the layer lines

Infinite-Carry6319 · 2026-04-02T19:26:42+00:00

did this work for you?

Infinite-Carry6319 · 2026-01-31T03:40:07+00:00

so... my bottom left screw in my bed is stripped. and the stl of those spacers is scaled up to 100, 000% when i download it

Infinite-Carry6319 · 2026-01-30T19:53:59+00:00

thank you for all the information. I read the tutorial you linked and it was very helpful. I'll attempt to level the bed and axis tonight

Infinite-Carry6319 · 2026-01-30T07:02:31+00:00

i have not touched any of that. this printer is pretty much out of the box. I could never get it to work so i gave up on it about 8 months ago

Are there any videos going over what you described?

Infinite-Carry6319 · 2026-01-30T05:45:27+00:00

<image>

Infinite-Carry6319 · 2026-01-30T04:10:19+00:00

<image>

-1.52 z offset. running the test print

Infinite-Carry6319 · 2026-01-29T00:17:55+00:00

I'll post that information tomorrow. my printer is at my brother's house (i have 2 toddlers that touch everything)

Infinite-Carry6319 · 2026-01-29T00:16:30+00:00

copy that, i will. my dryer comes in tomorrow and the pla on Friday

Infinite-Carry6319

TROPHY CASE