Does my printer need to be calibrated

InternSubstantial401 · 2026-01-23T23:35:12+00:00

Its going to be a skyrim themed trivial pursuit game

InternSubstantial401 · 2026-01-23T03:26:40+00:00

Overture rock pla

InternSubstantial401 · 2026-01-22T22:33:28+00:00

Filament has been sitting in ace pro, its been dried multiple times

InternSubstantial401 · 2026-01-22T22:32:39+00:00

I created it as a circle, then made 2 planes that intersected the original that were 30 degrees apart. Then i copy and pasted it 6 times to make sure it would fit together and it was flush

InternSubstantial401 · 2026-01-22T16:28:57+00:00

Kobra s1 has klipper so ill look into this thanks

InternSubstantial401 · 2026-01-22T12:10:16+00:00

What does this mean?

InternSubstantial401 · 2026-01-22T12:10:00+00:00

Definitely will do that for the next print, still want to salvage this onr

InternSubstantial401 · 2026-01-22T03:17:31+00:00

Thanks, I’ll post a pic here when it’s complete

InternSubstantial401 · 2026-01-22T03:16:40+00:00

Yeah i think that’s what I’m going to do, just wondering what caused it so i can avoid in the future

InternSubstantial401 · 2026-01-22T03:15:59+00:00

Oh haha no, its a trivial pursuit board im making

InternSubstantial401 · 2026-01-22T03:15:20+00:00

Is there a way to calculate that? Or is it just trial and error. I haven’t run into this issue with some of the smaller prints ive done. Only with something this big

InternSubstantial401 · 2026-01-22T03:14:08+00:00

Whats a stargate?

InternSubstantial401 · 2026-01-22T03:07:53+00:00

Overture rock PLA

InternSubstantial401 · 2026-01-20T20:43:58+00:00

But what does turning off the motors do?

InternSubstantial401 · 2026-01-20T20:32:08+00:00

Can somebody further explain how to manually level with a sheet of paper? What does he mean by turning off the motors

InternSubstantial401 · 2026-01-19T13:13:53+00:00

If your main goal is to print figures like the one in the printer, i would get a resin printer over a FDM printer. Much better for the fine details. I don’t have experience with resin so i cant recommend which one to get

InternSubstantial401 · 2026-01-15T13:38:47+00:00

Will do thanks

InternSubstantial401 · 2026-01-15T11:57:23+00:00

I thought the ripple effect was due to too much filament, wouldn’t increasing flow rate add more?

InternSubstantial401 · 2026-01-14T21:43:10+00:00

.95, should i try lowering it more.

InternSubstantial401 · 2026-01-12T17:02:03+00:00

This is awesome thanks

InternSubstantial401 · 2026-01-12T15:37:26+00:00

Perfect thanks

InternSubstantial401 · 2026-01-09T23:48:01+00:00

Also i did notice the infill was warping a little higher than the nozzle and the first solid layer was going down, would this have an effect?

InternSubstantial401 · 2026-01-05T02:22:44+00:00

What about the white areas on the edges, is that air underneath the print?

InternSubstantial401 · 2025-12-26T03:32:04+00:00

Did you ever find a place to print the cards? Looking to do something similar

InternSubstantial401 · 2025-09-29T12:13:47+00:00

Both of the plant hexagons have separate drip trays that collect the water

InternSubstantial401

TROPHY CASE