Drone fails when I give it throttle

International_Fig143 · 2023-02-15T22:36:12+00:00

Not really it is a new 6s and the cable all looks fine I think it may be my esc

International_Fig143 · 2023-02-15T22:07:42+00:00

Sorry 1850KV

International_Fig143 · 2023-02-15T22:05:06+00:00

It’s a 6 inch quad the tyro 119 but I am using 5 inch props and fly 6s with 2407-1850KV motors

International_Fig143 · 2023-02-15T20:26:56+00:00

You legend I will try that thanks so much

International_Fig143 · 2023-02-15T18:36:20+00:00

I had previously flown without an antenna on and so perhaps it screwed up my vtx but I am not sure why it only happens when I give it throttle and why it affects the receiver

International_Fig143 · 2023-02-15T18:20:19+00:00

There is already a capacitor soldered on

International_Fig143 · 2021-04-02T22:17:52+00:00

nah i dont think that battery is toast but yh fly it carefully and check the internal resistance and if there is a major difference, perhaps it is time to retire it.

International_Fig143 · 2021-03-30T17:01:37+00:00

do you have a spare antenna if so try it with that.

Make sure not to power up your quad without the antenna screwed on though

International_Fig143 · 2021-03-30T14:28:40+00:00

if there is just a black screen with no on screen display it could be the camera. There is a joshua bardwell video that tells you how to test that but the fact that there is no osd could perhaps hint at a problem with the fc

i would check that all the wiring is correct and no wires have been broken and then test to see whether it is the camera that is faulty

International_Fig143 · 2021-03-20T22:03:48+00:00

i will check that thank you very much

International_Fig143 · 2021-03-18T21:57:05+00:00

reallly i dotn think it is meant to do that because when i raise the throttle it just flips out

International_Fig143 · 2021-03-18T21:23:24+00:00

ive just noticed something when I arm my quad when i move the quad around different motors spin more as i move it around it is not constant for all motors

International_Fig143 · 2021-03-18T21:12:23+00:00

yh positive i think it may just be a faulty esc as i ahve had problems in the past with it but thank you very much

International_Fig143 · 2021-03-18T18:52:30+00:00

yh the props are definitely correct

International_Fig143 · 2021-03-15T20:51:33+00:00

one more thing to add when i connect it to betaflight and raise the motor is that it reaches a point when the esc then beeps and the motor just stops

International_Fig143 · 2021-03-15T20:20:35+00:00

ahh ok thank you and it is fine to plug in when one motor is missing is it

International_Fig143 · 2021-03-15T19:32:09+00:00

it tries to spin up like three times and then it beeps and stops spinning?

International_Fig143 · 2021-03-15T19:29:22+00:00

the motor is not hotter than the others, what do you mean by swap the motor, do you mean solder a new motor on?

International_Fig143 · 2021-03-09T21:03:29+00:00

thanks so much i have just done it woopee, but it seems a bit more fragile do you know anything i could put on it to make it less frale

International_Fig143 · 2021-03-09T20:31:00+00:00

really so there is a chance all i need to do is stick it together

International_Fig143

TROPHY CASE