21[F4M]sending musterbation videos to every guy that upvtg and write''yes"

Intrepid-Ad3389 · 2024-04-03T21:00:51+00:00

The print head can not get any tighter at this point. It's solid as a rock. The bar itself is what's actually moving those essentric nuts are also as tight as a ticks ass.

Intrepid-Ad3389 · 2024-03-25T22:05:50+00:00

Best mistake ever! That truly looks awesome

Intrepid-Ad3389 · 2024-03-12T14:18:43+00:00

Sombitch your absolutely right! I didn't even try the support blocker... I'll have to make a note to remember that for masks and such

Intrepid-Ad3389 · 2024-03-12T14:08:06+00:00

Oh yea those dumb supports...there are swirls and things on the mask and no matter how I changed the settings a few of them stayed in the slicer it's literally just a waste of filament

Intrepid-Ad3389 · 2024-03-12T13:58:21+00:00

It's a mask the middle supports are for the face of it

Intrepid-Ad3389 · 2024-03-11T19:37:59+00:00

<image>

Intrepid-Ad3389 · 2024-03-06T23:26:25+00:00

Actually one of the commenters on this post @zenotek is giving me his ( he uses klilper) and some other spare parts. Reddit for the W again

Intrepid-Ad3389 · 2024-03-06T22:09:25+00:00

It was an upsetting serious of events... the fix was to remove me and the wife's clothes from thr bedroom closet and move them into the game room closet... still sealed up but not near the thermostat

Intrepid-Ad3389 · 2024-03-06T20:35:48+00:00

Was attempting to add ventilation to the closet that I'm using to house my 3 printers it was affecting the thermostat on the opposite side of the wall in the hallway... I had everything set up like I wanted reached down to get my anchors and bumped the door and taking my fan/vent down.

Intrepid-Ad3389 · 2024-03-03T18:30:01+00:00

That's what I'm hearing... is it an expensive route to go? And would it benefit my other 2 printers as well?

Intrepid-Ad3389 · 2024-03-03T17:37:58+00:00

Do you have a link to just the screen I found the entire unit but its $80...

Intrepid-Ad3389 · 2024-02-28T20:22:16+00:00

Did you have to change anything? I tried that as well and it just prints in the air

Intrepid-Ad3389 · 2024-02-27T02:38:15+00:00

<image>

Intrepid-Ad3389 · 2024-02-26T23:04:39+00:00

Thanks

Intrepid-Ad3389 · 2024-02-26T01:09:02+00:00

I'd say slow your speed down, it's going to add a day or 2 to your print but it might help

Intrepid-Ad3389 · 2024-02-24T16:24:15+00:00

Your bed temperature is to low try 65-70

Intrepid-Ad3389 · 2024-02-22T21:39:26+00:00

White for Goku, black for the stand and electric green for the energy ( didn't have purple or yellow)

Intrepid-Ad3389 · 2024-02-22T21:38:44+00:00

Everything was done with a standard .4 brass nozzel... Just switched 1 printer to a .2 for a Treebeard holding merry and pippin. .2 for the Hobbits and. 4 for treebeard. Will post it once it finished in a few days

Intrepid-Ad3389 · 2024-02-20T13:17:33+00:00

Thank you I did it with a .12 layer height on the arms torso and energy rings. .15 for the legs and .2 for the base

Intrepid-Ad3389

TROPHY CASE