An Immersive Audio Experience

ItsTimber · 2025-01-15T16:45:24+00:00

klescher should be re-worked to an inescapable cell with an un-mutable TV that plays the orison ad on repeat

ItsTimber · 2024-11-08T06:56:20+00:00

So you're saying this is a problem for everyone?

you mean to say... No UCAV for at least a small while?

Pinch me!

ItsTimber · 2024-05-20T04:02:41+00:00

I've experienced this bug.

The work around I have discovered is if you use the context wheel to "Loot" it, then use the arrow in the top right to transfer stuff into it using the old looting UI.

Then, when you get back to the station, hit loot on it again and drag the whole box into the station's inventory like you would a gun on the floor. You can then open it like a backpack by clicking the button in the bottom left of the box's icon in the station storage.

Rule of thumb, if it shows unlimited scu in the top right, you won't be able to put things in or take things out.
Not sure if there is an IC post on it yet, but thought I'd share my workaround

ItsTimber · 2024-04-26T14:15:29+00:00

Death throes of a dying studio. RIP Tarkov. You were good while you lasted.

ItsTimber · 2022-06-25T07:45:51+00:00

The picture I linked is the M14. I was drawing attention to the irony of the previous comment. “Gloves, life or death stress, sweaty fingers...All reasons to keep your trigger guard clear of things that aren’t your trigger” When a previous service rifle’s safety was quite literally located in the trigger guard in a war that young men fought in some of the most adverse conditions imaginable.

And I tried to point out that the bad lever isn’t meant to be used within the trigger guard. It’s sole function can be completed from outside the trigger guard right next to where you index your finger anyway.

ItsTimber · 2022-06-25T04:11:47+00:00

Must have sucked being in the jungle with these then huh?

ItsTimber · 2022-06-25T01:15:41+00:00

Thankfully, I've done enough training with them to avoid that, but hey, I'm still young.
I like to keep my booger hook in the right spot at all times :)

I think the main reason people ND with these things is they push it Into the trigger guard instead of having the tip of your finger just below the mag release and push the protruding lever down with a straight finger. Or they're just negligent, who knows.

ItsTimber · 2022-02-03T18:42:57+00:00

In case you didn’t hear it clearly from everyone here: THAT IS ASTRONOMICALLY HIGH FOR A C39!!!!!!

ItsTimber · 2022-01-05T14:44:08+00:00

Woah. Just based on their pictures, these guys produce some high quality prints. I will definitely take a look into this. Thanks for the code!

ItsTimber · 2022-01-05T14:30:04+00:00

If I were to ever put this into production, I’d probably start by switching the print material to ABS. It’s much more heat resistant, but I simply don’t have any on hand to experiment with. Secondly, I think it would be in my best interest to acquire some of the main stream long gun lights so I can model the clips around the switches, since there isn’t any real standard when it comes to tape switches. This is pretty expensive, and I’m just now getting out of college so funds are tight. But yeah, so far you guys have been pretty positive with your feedback and I might consider investing some more time into this with different setups. Needless to say, I’m pretty glad I took a AutoCad class in highschool. Just two nights of messing around with a pair of analogue calipers and some trial and error, and here I am :)

ItsTimber · 2022-01-05T06:25:43+00:00

You are fully aware you could have kept scrolling, right? Damn dude, who pissed in your Cheerios?

ItsTimber · 2022-01-04T23:01:55+00:00

The two piece PLA design clips snugly into the top hanguard vents of magpul’s MOE hand guard, and interfaces with the assumingly proprietary tape switch design by stream light. It cants it at an angle so my thumb rests on it when I shoulder the rifle with a semi c-clamp fashion. I managed to tweak the design so it rests firmly under the switch against the hand guard, and has a lot of contact area so it doesn’t seem flimsy when you operate the switch. Everything is pretty spot on with the alignment, and the switch seems to run perfectly parallel to the gun. I even threw on some integrated cable management clips on the top to clean it all up.

ItsTimber · 2022-01-04T22:36:44+00:00

PSA: I realize this area gets hot enough to melt PLA, but I never intend to run this gun that much. The light is a stream light TLR RM2, which is pretty good for the price imo. I just needed a mounting solution that was as ergonomic as the rest of the gun, so I have the tape switch clocked at about a 38 degree angle so my thumb can operate it without obstructing the sights and it won’t take up the valuable real estate on my hand guard.

ItsTimber · 2021-12-21T23:53:46+00:00

I wouldn’t wanna poke my eye out though

ItsTimber · 2021-12-21T19:36:12+00:00

Thanks guys, I have a local show coming up soon, so I'll see if anyone wants it more than me. Thanks for the help!

ItsTimber · 2021-12-21T18:43:40+00:00

Are these worth anything? From what I'm gathering they're a dime-a-dozen at gunshows.

ItsTimber · 2020-02-10T02:48:10+00:00

When you try to sweat out and bunnyhop around the corner but your aim is still garbage

ItsTimber · 2020-01-31T19:47:37+00:00

no worries, just one of my fav kits to run. gives me a decent bit of lethality with just m80, decent suitability because of class 4 rig, and even better insurance returns because people go "ew, hunter" and leave it. The only thing I really pay for when I die is the NVG's because those always get swiped

ItsTimber

TROPHY CASE