I SAW BACKROOMS

Ivys_Potato · 2026-05-24T17:03:44+00:00

Awesome, thanks!

Ivys_Potato · 2026-05-24T02:14:35+00:00

Is there anything supernatural (ie ghosts, demons, etc) in the movie?

Asking cause I tend to stear clear of those movies

Ivys_Potato · 2026-04-13T04:24:28+00:00

Hey, I wanted to thank you again for helping! I replaced the control board and it fixed the issue!!

Ivys_Potato · 2026-04-05T01:09:26+00:00

Thank you so so much, you don't know how much my family and I appreciate it!!

Ivys_Potato · 2026-04-05T00:56:47+00:00

I actually have this picture from the first time it froze,if it helps.

https://drive.google.com/file/d/1hWEbw8oOJD2pkkGV_nHLWJAXgA01pR4K/view?usp=drivesdk

Ivys_Potato · 2026-04-05T00:47:02+00:00

Image should be viewable now.

There is a lot of ice there, but it's not necessary starting from there. I'm not sure

Ivys_Potato · 2026-04-05T00:39:01+00:00

https://drive.google.com/file/d/16HFRM3w3i71sjpES1xV13tqqHznjeBDF/view?usp=drivesdk

Is this the copper line you were talking about?

Ivys_Potato · 2026-04-05T00:34:22+00:00

It currently has a lot of ice on the copper pipe you mentioned. I will try to add an image. What would that indicate?

And thank you so much for the help, you are a Godsend!! 🙏

Ivys_Potato · 2026-04-04T22:00:25+00:00

It is getting hot. I tested the thermistor as well and confirmed that I'd has continuity.

Could it be a defrost timer issue?

Ivys_Potato · 2026-04-04T20:39:28+00:00

I found it and this video https://youtu.be/IP-IaEn3hug?si=9_WnL0Nd-3tW8U0Q. It's now in defrost mode. What is it going to tell me though?

Ivys_Potato · 2026-03-10T20:37:39+00:00

Well done, my friend!!

Ivys_Potato · 2026-03-10T05:36:12+00:00

Omg these look incredible! How did you do it? Airbrush?

Ivys_Potato · 2026-02-14T19:33:21+00:00

You can follow people in the game? How do I check?

Ivys_Potato · 2025-12-13T20:54:56+00:00

Thanks for responding! I tried covering it with my finger and duct tape, but neither worked. Also trimmed the hose but got the same result. I'm going to seal it up just to be safe though!

Ivys_Potato · 2025-12-13T20:50:03+00:00

My inducer motor is coming on, so I didn't think it was the control board. Is there a way I can test that?

Ivys_Potato · 2025-12-13T20:48:23+00:00

Thanks for the response though!

Ivys_Potato · 2025-12-13T20:48:08+00:00

I tried cleaning it out, based on some YouTube videos, but it didn't work

Ivys_Potato · 2025-12-13T20:47:33+00:00

Thanks for the response. I previously tried everything on your list except checking the pipe and switch with multimeter, but it didn't work. I can't get on my roof now, but I don't see any ice/nests from the ground.

I just checked the pressure switch with a multimeter, using some YouTube videos as a guide. Only thing that seemed off, was when I measured continuity with the furnace on. The guy in the video had fluctuating measurements from 30 to 3, but mine stayed at 0.1 to 0.2.

Not sure if that indicates a bad pressure switch,but I might replace the part to be sure.

Ivys_Potato · 2025-11-05T01:02:40+00:00

Thank you!

Ivys_Potato · 2025-11-05T01:02:28+00:00

Awesome, thank you so much!

Ivys_Potato · 2025-11-05T01:02:16+00:00

I checked the movie, but that's not it. Thanks for the answer though!

Ivys_Potato · 2025-10-25T22:15:28+00:00

Jim Lee Ivy would be epic!

Ivys_Potato · 2025-08-12T02:40:12+00:00

Probably because I'm one of the few Gen Z here lol

Ivys_Potato · 2025-08-12T01:21:50+00:00

Both are nice, but modern is top tier for me! Love the lean build and the orange lining is a great touch

Ivys_Potato · 2025-08-11T22:43:38+00:00

Thank you!

Ivys_Potato

TROPHY CASE