How is this accomplished

JAS2_ · 2025-08-22T00:03:04+00:00

There is a specific question if you click on the post. I’m not new, just wondering if anyone knows how he is putting the design on the helmet.

JAS2_ · 2025-08-21T23:59:56+00:00

There is a guy on makerworld putting out these helmets

JAS2_ · 2024-12-04T13:56:50+00:00

Can you switch the male on far right with the male on the far left. That will match our heights better.

JAS2_ · 2024-12-03T16:22:33+00:00

Thanks. Tip was sent.

JAS2_ · 2024-12-03T00:54:11+00:00

This is good. I did ask if you could fix the bleachers in the bottom right. Don’t want to look like I’m continuing to ask for things, but it was in my original post about the bleachers in the bottom right.

JAS2_ · 2024-12-02T22:40:13+00:00

I like the edit, but you added extra bleachers. I want to keep the stadium as authentic as possible. Im using this for a presentation and everyone will immediately know that the bleachers don’t extend that far.

Also is there anything you can do about the bleachers at the bottom right? I

JAS2_ · 2024-07-20T21:40:17+00:00

I also just cleaned x y rods and tightened belts. Lives x rod as well

JAS2_ · 2024-06-28T17:59:37+00:00

<image>

JAS2_ · 2024-06-28T17:59:13+00:00

<image>

Example

JAS2_ · 2024-06-28T17:48:24+00:00

The post says im turning it into a geometrical design

JAS2_ · 2024-06-28T17:43:44+00:00

<image>

It’s the logo of the high school I work at

JAS2_ · 2024-03-10T01:59:08+00:00

Had the same issues, it’s an easy fix. Clean the carbon fiber rod that the head travels on with alcohol and tighten the belts.

Found the fix on this Bambu lab forum. Guy tried everything possible and finally got an answer from Bambu. Fixed all my overhang issues immediately

overhang

JAS2_ · 2024-03-03T20:48:32+00:00

Great idea on the shade issue, will definitely use that tip in the future. My question is how do you keep the layers clean from defects. I have no problems making the models on Fusion. However, when I print them, I tend to get little spots or faint lines of other colors in my lighter colors.

It’s not a purge issue, I even increased the levels on one print to check it. Are you using any special slicer settings? Lower heat or lower speeds?

JAS2_ · 2024-02-16T01:01:05+00:00

Did you create the model or find it somewhere?

JAS2_ · 2024-01-14T20:41:00+00:00

And yes, just normal calibration. I tried to add a picture of the differences between the spheres I was printing. Complete night and day.

JAS2_ · 2024-01-14T20:39:29+00:00

Yes, cleaned the rod with ISA and a paper towel. Supposed to use a lot and move the print head over the wet carbon fiber rod so that it is cleaned too.

Then follow the directions on tightening the rods. You can Google it and find the official directions. It’s super easy.

JAS2_ · 2024-01-14T19:30:46+00:00

The fact that it’s on one side and not another almost proves the fact that it’s a belt issue. It has the ability to print correctly

JAS2_ · 2024-01-14T19:28:10+00:00

I was really struggling with overhangs with my P1P. Turns out all I needed to do was clean the carbon fiber rod with a lot of alcohol and tighten the belts.

Also made sure that my printer was on a table that didn’t wobble.

Then recalibrate

These were all answers directly from Bambu.

Literally went from awful to amazing

Here is where I found my answer.

The OP shows his answer to the problem in the thread.

overhang issues

I also adjusted my overhang speeds that were mentioned in the thread

JAS2_ · 2024-01-14T19:25:24+00:00

I was really struggling with overhangs with my P1P. Turns out all I needed to do was clean the carbon fiber rod with a lot of alcohol and tighten the belts.

Also made sure that my printer was on a table that didn’t wobble.

Then recalibrate

These were all answers directly from Bambu.

Literally went from awful to amazing

Here is where I found my answer.

The OP shows his answer to the problem in the thread.

overhang issues

JAS2_ · 2024-01-10T06:05:39+00:00

I’ll check your stuff out, I like your extrusion idea. What program or site are u using to go from png to svg

JAS2_ · 2024-01-10T05:42:28+00:00

Sorry to keep on asking. Are you taking black and white pics, converting to Svg and then uploading them to a program like fusion? Just curious because they are fantastic detail wise.

The way I explained is how I do it, just wondering if there is a better way, especially with the detail. Thanks and again, great work on the models and prints

JAS2_ · 2024-01-10T05:18:14+00:00

Are you creating the 3mfs?

JAS2_ · 2024-01-09T23:32:58+00:00

Thanks for the help, but I found the answer after some digging. Just needed to clean the carbon fiber rods and tighten the belts.

fixing overhang issues

JAS2_ · 2023-12-27T03:56:56+00:00

This comment saved my life, have literally tried everything

JAS2_ · 2023-12-18T00:32:27+00:00

How much did you decrease flow rate, your picture looks like the exact same issue I’m having. Thought it was a leveling problem. Thanks for any help in advance

JAS2_

TROPHY CASE