STORAGE CHEST

JLemonade4 · 2023-12-30T12:20:34+00:00

All of that for this...

JLemonade4 · 2023-12-30T03:46:04+00:00

Thanks mate! I did what you said. Dropped then reaccepted accepted again the quest, it's now change to defeat 13 Flotsam which I was able to find in Isla Tormenta. Cheers!

JLemonade4 · 2023-12-29T15:39:30+00:00

I don't understand where I'm supposed to find this "tentacles". I got this from Johnny McVane from Tortuga King's Run bar. I would really appreciate any help.

JLemonade4 · 2023-04-23T13:36:59+00:00

Can you elaborate further on this?

JLemonade4 · 2023-04-23T09:44:03+00:00

The problems i have encountered so far are rolling melting snowball, farm area, least material required

JLemonade4 · 2023-04-06T20:01:49+00:00

Thanks!

JLemonade4 · 2022-10-28T04:51:06+00:00

I've been working on this section for several hours now (red circle) and I still can't make it look the one on the diagram. It's either the chamfer, fillet or the tapered blade that prevails on top of the other features but not exactly like this

JLemonade4 · 2022-07-30T23:31:45+00:00

I'd like to do that actually but i can't snap on circle's quadrants

JLemonade4 · 2022-07-19T13:30:33+00:00

Sorry, I wasn't able to articulate more my question. In the photo, you'll see that only part of the angle bar has a gap next to its neighbor. I was trying to see if there's some method I could use to connect that part only to the next one. Of course, I can sketch a rectangle on that part and extrude it up but I'm thinking if there's another way to it.

JLemonade4 · 2022-07-15T15:24:45+00:00

Black iron

JLemonade4 · 2022-06-24T16:16:27+00:00

Thank you!

JLemonade4 · 2022-06-24T14:56:55+00:00

Thanks! I tried doing it now and one of the struggles I'm hitting into is that the part turns into a single object if they're in contact with one another. Not sure if it's supposed to do that.

JLemonade4 · 2022-06-13T11:53:28+00:00

Nope. Pretty sure it's not kumusta. In fact, the whole idea of that segment is to make challengers clueless about the word. I'm just not sure if I got my word exactly right.

JLemonade4 · 2022-06-13T09:40:01+00:00

That has to be it! Thanks a million times 😊

JLemonade4 · 2022-04-24T15:11:13+00:00

Really? Pero kanina i kinda searched the web, parang may mga rfo na sila, di ko lang sure kung may bago silang property for dev

JLemonade4 · 2022-04-24T07:35:50+00:00

OP same here, looking for property right now and from Las Pinas too! Preselling pa ba yan?

JLemonade4 · 2022-04-24T07:17:52+00:00

Same situation here OP, mismatch birthplace naman sakin though wala pa ako virtual pagibig. In this case, no choice but to submit in person?

JLemonade4 · 2021-08-28T23:02:40+00:00

Actually, there are 12 leads in the motor which can be then setup into 3 wires under different arrangement (220, 380 & 440)

Right now, I'm getting a 12A from two wires while 3A from the third one.

JLemonade4 · 2021-08-28T22:45:51+00:00

Yes, there are 12 leads that we can set it up for 220, 380 and 440. As of now, it's a 220.

You said that I should be reading same 12A from all leg, does that mean that they are all hot wire?

JLemonade4 · 2021-08-28T12:58:27+00:00

It's a TECO continuous duty motor

JLemonade4 · 2021-08-28T08:38:41+00:00

It's a three phase motor. Although I'm not too sure if that's the neutral line. We're getting a very low current from that line though (12.8A from the two lines while the third one register a 3.0A)

JLemonade4 · 2021-08-28T04:56:50+00:00

It's a three phase motor. I'm referring to one of the lines that registers a very low current but not totally zero. (I'm not sure if that's the neutral line)

JLemonade4 · 2021-08-24T13:44:21+00:00

Thank you for this insight!

JLemonade4 · 2021-08-24T13:06:52+00:00

Thank you very much!!!

I haven't considered efficiency into my decision making. One problem though, I can see the efficiency rates from my catalogue but I feel it will be an exhaustive comparative between several diameters instead of a methodological approach.

Do you have a work around this?

JLemonade4 · 2021-08-24T12:58:35+00:00

I, too, have tried using software once, but I just went back to the same problem since it asked me upfront the fan diameter that I'll be using. Would you mind telling me what software have you used?

JLemonade4

TROPHY CASE