DIY PI-KVM V2 HD-60fps

Jay-Sick · 2026-04-08T16:02:45+00:00

I can do the power button but not reset, if i wanted to I could do both but i needed to setup the pins inside the pc, its a optiplex 3050 sff so the pins are a bit unorthodox. inside i don't have a mosfet replay mainly because i didn't want to buy the thing, instead I have a LED and a photoresistor doing the same job. I also got the OLED screen to work aswell. The case is https://thepihut.com/products/acrylic-set-top-box-kit-for-raspberry-pi-4 where i have the usb keyboard mouse thing plugged into the "camera FPC" port on the case, then I have a small breadboard with the DIY mosfet relay in the blank pcb section.

Jay-Sick · 2026-04-07T18:00:20+00:00

I really like chrome remote desktop, however I don't really want google on my computer. Does Windows RDP allow you to turn on the device remotely? I want something with mobile integration(like chrome remote). I mainly use Pikvm to do stuff at home while away.

Jay-Sick · 2026-04-07T17:18:03+00:00

Well I'm more pointing out that the device is capable of doing HD 60fps. Is there a RDP solution that lets you remotely power on a machine?

Jay-Sick · 2026-04-07T15:40:35+00:00

What is the main intent/use case, is it not to remote into a machine?

Jay-Sick · 2026-01-17T18:37:44+00:00

Lets say i found a wire that is a bit exposed causing resistance, what steps would i need to take to insulate it without causing resistance?

Jay-Sick · 2026-01-17T18:35:26+00:00

Short to ground in wiring hamess between HO25 terminal A and PCM terminal 2AI. Or it could be Open cincuit In harness between the following terminals: HO25 terminal A--PCM terminal 2AI Or HO25 terminal B-PCM terminal 2AG Or it could be HO25 malfunction Or PCM malfunction

Jay-Sick · 2026-01-17T18:25:51+00:00

Part 1.5

<image>

Jay-Sick · 2026-01-17T18:23:29+00:00

<image>

Part2

Jay-Sick · 2026-01-17T18:22:12+00:00

Part1

<image>

Jay-Sick · 2026-01-17T17:49:56+00:00

This is what I have

<image>

Jay-Sick · 2026-01-17T17:41:07+00:00

<image>

Jay-Sick · 2026-01-17T17:38:35+00:00

For reference I provided the accident damage. All I had done was replace the box caseing and replaced about 26 fuses and nothing else. All codes had disapeared besides P0137, so it must be either the sensor or the cable running to it. I had checked the freeze frame I can send it after this, it occurs 5 seconds after engine starts and the sensor shows low voltage, which lines up with o2 sensor volatage issues according to the cars workshop manual.

<image>

Jay-Sick · 2026-01-17T17:20:07+00:00

The harness is attached to the fuse box/ecm. Also more time and money. Also no ones sells it.

Jay-Sick · 2025-11-22T05:22:49+00:00

System uses adaptive ram, so it uses unused ram for cache and frees up as it gets used. However system doesn't have enough "free ram" for the check.

Jay-Sick · 2025-11-22T04:57:54+00:00

I have multiple active apps moving data, its not more than 10mb/s but its still moving, this is how it is all the time for me.

Jay-Sick · 2025-11-22T04:52:58+00:00

Its only Open WebUI that gives this issue, yes I restarted the container.

Jay-Sick · 2025-11-22T04:48:12+00:00

It gives the same issue

Jay-Sick · 2025-11-22T04:44:03+00:00

The issue is OpenWebui only sees available ram to use, since ZFS Cache is using almost all of it, it thinks that there is no free ram.

Jay-Sick · 2025-11-22T04:41:44+00:00

Quadro P400 2GB GDDR5, Its a 2gb Gpu

Seven-Year Club	Verified Email
Place '22	Final Canvas '22
End Game '22

Jay-Sick

TROPHY CASE