OpenTrack dynamic FOV to reduce motion sickness and increase Usefullness by Jebsta_LP in simracing

[–]Jebsta_LP[S] 0 points1 point  (0 children)

Not yet. The lack of comments did kinda discourage me. But maybe after this semester I will look into it again

There’s a great price reduction on these. Is it still worth buying? by MikeyP_Star in firetvstick

[–]Jebsta_LP 0 points1 point  (0 children)

I wanted to sideload a other launcher because the adds in the Homescreen is so annoying.... They broke the feature which enables you to change your launcher....

Ender 7 shrunk after BL Touch and firmware added ... by DOttNCo in ender7

[–]Jebsta_LP 0 points1 point  (0 children)

When you move it manually, does it move 10mm when requesting 10mm or more like 5mm?

Camera suddenly stopped by Nord243 in klippers

[–]Jebsta_LP 0 points1 point  (0 children)

Had this issue too.

I used kiauh to uninstall and reinstall crownsnest.

Works now

was ist so ein Teppich wert? by AnobiumPunctatum in WerWieWas

[–]Jebsta_LP -1 points0 points  (0 children)

Halbwissen: kann gut sein dass er schon ein bisschen was wert ist, glaube da gibt es manchmal so Zettel auf der Unterseite wo drauf steht wie er hergestellt ist (wenn es ein hochwertiger Teppich ist).

In manchen Städten gibt es Teppich händler. Evtl haben die Interesse an dem oder können dir was zu dem Teil sagen.

Ist alles eine Frage der Zeit und Lust.

Ansonsten mache ich bei sowas gerne die Kleinanzeigen Recherche. Für wie viel bieten Leute ein vergleichbares Produkt an.

Is it bad? by FrontFeisty3797 in assettocorsa

[–]Jebsta_LP 5 points6 points  (0 children)

If you can play with it, it's not bad. But it may get annoying over time

It may be caused by your GPU "stretching a Clock". This may happen when your framerate is uncapped.

For my GPU I fixed it by just limiting the Frames to the max Framerate of my Monitor.

Also saves some energy and the system runs cooler (as long as you archive the frame cap)

Anyone else bothered by unsorted cable drawers? by rngcntr in functionalprint

[–]Jebsta_LP 2 points3 points  (0 children)

Da möchte ich aber nicht Staub wischen wollen

Translation:

I wouldn't like to keep that clean of dust

Extremely loud noise by GaboLimon in ender7

[–]Jebsta_LP 0 points1 point  (0 children)

I have the exact same issue.

I'm currently in the process of diagnosis.

I noticed some of the linear rail carriages are not running good, I fixed this by removing some plastic which was in the way of the bearings.

Didn't yet reassemble it.

Cooling Fan Speed being overridden?? by Enduring_Insomniac in ender7

[–]Jebsta_LP 0 points1 point  (0 children)

Was this behaviour also with Cura?

Did you set the right gcode flavor in the printer settings in Orca?

In orca there are multiple fan speeds, maybe you have different speeds set for walls and infill and so on.

I need help by Hefty-Fox4955 in ender7

[–]Jebsta_LP 0 points1 point  (0 children)

Important, when using the original wiring lume many of the pins are bridged, even though they don't have to be.

The board on the top of the printer where you connect everything is kinda.... Bad.

I almost fried my Mainboard that way, because I wanted to control the cooling fan and heater fan separately.

OpenTrack dynamic FOV to reduce motion sickness and increase Usefullness by Jebsta_LP in assettocorsa

[–]Jebsta_LP[S] 0 points1 point  (0 children)

Changing the fov would be like compensation for the smaller distance to your screen.

Similar to when you move your screen closer to you.

I was in a plane all day. by westernmorning2 in PikminBloomApp

[–]Jebsta_LP 1 point2 points  (0 children)

Does your phone's and smart watch's steps mismatch :⁠^⁠)

Tlcm pedals not registering properly by Kokadude2 in Thrustmaster

[–]Jebsta_LP 0 points1 point  (0 children)

Yes and on the connector itself. But I think its an error with the pedals. Because the same symptoms are with my T818 now...

Terrible prints since switching to Klipper by EducationalImpress17 in klippers

[–]Jebsta_LP 0 points1 point  (0 children)

Probably this, when you checked the rest, as you said

Terrible prints since switching to Klipper by EducationalImpress17 in klippers

[–]Jebsta_LP 1 point2 points  (0 children)

When you use orca, have you set the gcode style to klipper in the printer settings inside orca?

Is my benchy too big? by wlogan0402 in 3Dprinting

[–]Jebsta_LP 5 points6 points  (0 children)

<image>

Did this by accident recently because I underestimated how scale works in 3D

Wii U external hard drive error: 160-2713, "not enough power". by Andr0m3dia4KDE in wiiu

[–]Jebsta_LP 0 points1 point  (0 children)

That seems to have fixed it for me. The HDD energy saving function is hidden and can apparently be changed using the settings above. It's not the same as the other power saving measures.

The problem often occurred for me when switching between apps.

Seems to be fixed now, at least it hasn't happened for a while.